The following is an overview of the user manual for the Z-Wave product PIR Sensor Lux (PLBW10100)from ABUS. To view other Z-Wave products and manuals from ABUS follow that link.
Overview
In addition, the sensitivity can be flexibly adjusted and the detector is pet-immune if desired.
PIR supports 80° viewing angle and up to 8m range.
Security
As a Z-Wave Plus certified product, PIR Sensor Lux supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
ABUS describes PIR Sensor Lux as having the following features:
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: The DSK code (Device-Specific Key) is the device-specific key of your device and is required for secure inclusion (teach-in) via S2 on the Z-Wave controller. The first 5 digits of the DSK code can be found on the QR Code on the back of the product. Please enter them in the inclusion process when prompted. Alternatively, you can transfer the entire DSK code that you find on the enclosed DSK card to the Z-Wave controller via QR Code Scan. Please keep the DSK card in a safe place!
Hint:
We recommend the secure S2 inclusion (must be supported by the Z-Wave controller) Please enter the 5 digits of the DSK code (bottom of the device) or the entire DSK code (QR code) when prompted.
Activate the inclusion mode (teach-in mode) on the Z-Wave controller. (for more details, please refer to the Z-Wave controller's user manual)
Press the "+" button (Add / Inclusion) in your Z-Wave app and follow the instructions to set the Z-Wave controller to inclusion mode.
Keep the device within reach of the Z-Wave controller.
Remove the safety strip from the battery compartment. We recommend using only the original Duracell battery supplied.
Press the Link button 3 times quickly (within 1.5 seconds) to start the inclusion on the device.
The LED starts flashing red for up to 60 seconds
The successful inclusion is displayed in the app or on the Z-Wave controller and the status LED on the device lights up red for 2 seconds.
Repeat the inclusion process if it was not successful.
If a new attempt fails as well, first carry out a factory reset on the device, see 2.5.
Activate the exclusion mode (learn mode) on the Z-Wave controller. (for more details, please refer to the Z-Wave controller's user manual)
Press the "-" button (Remove / Exclusion) in your Z-Wave app and follow the instructions to set the Z-Wave controller to Exclusion mode.
Press the Link button 3 times quickly (within 1.5 seconds) to start the exclusion on the device. The LED starts flashing red for up to 60 seconds
Successful exclusion is displayed in the app or on the Z-Wave controller and the status LED on the device lights up red for 2 seconds.
Press the Link button once to wake up the device. It will then establish a connection to the Z-Wave controller and transmit the current status.
Factory reset PIR Sensor Lux
Press and hold the Link button for at least 5 seconds. Release the button when the red LED stops blinking and lights up continuously. The device is now reset to factory settings.
Hint:
Please use this procedure only if the primary network controller is missing or otherwise not functional.
If the device is set to factory default, the status is set to "not included" and the association settings and possible configurations are reset to default.
N/A
N/A
Please note that this is a user manual PIR Sensor Lux from ABUS is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have PIR Sensor Lux and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.