Z-Wave Button (SHBE10000) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Z-Wave Button (SHBE10000)from ABUS. To view other Z-Wave products and manuals from ABUS follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


Z-Wave Button
SKU Code
Scenes programmed in the Z-Wave Gateway can be safely and quickly switched on and off at the touch of a button without having to open the app.

The rocker button has 2 buttons (top and bottom), for each button a distinction is made between short press, double press and long press.

This means that up to 3 different scenes can be switched on and off as the button can send a total of 6 different commands to the Z-Wave Gateway
With just one button, an entire room can be controlled. For example: heating up/down, lighting on /off and shutter up/down.

The button can either be glued to the wall or screwed. Alternatively, it can also be used on the move, for example on the bedside table or living room table.

The wireless button can be operated with 2 standard AAA batteries for up to 2 years without battery replacement.
Version #
HW: 1 FW: 1.00 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, Z-Wave Button supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


ABUS describes Z-Wave Button as having the following features:

  • Z-Wave Scene Type
  • Battery Quantity
  • Battery powered using AAA batteries
  • Color
  • Firmware updatable via a compatible Z-Wave gateway
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: Backside of the Base
Described in user Manual chapter 1.2, page 6

It can also be found on DSK Card
Described in user Manual chapter 1.6, Page 7

Activate the inclusion mode (teach-in mode) on the gateway. (for further details please refer to the gateways manual)
Press the "+" key (Add / Inclusion) in your Z-Wave app and follow the instructions to set the gateway to Inclusion mode.

Keep the device within range of the gateway.
Remove the fuse strip from the battery compartment.
The device supports automatic inclusion, i.e. it automatically goes into inclusion mode when it is powered and not yet connected to a gateway.
Alternative Inclusion:
If the security strip has already been removed, instead press the Link button 3 times quickly (within 1.5 seconds) to start the inclusion on the device.

Activate the exclusion mode (learn-out mode) at the gateway. (for further details please refer to the gateways manual)
Press the "-" key (Remove / Exclusion) in your Z-Wave app and follow the instructions to set the gateway to exclusion mode.

Press the Link button 3 times quickly (within 1.5 seconds) to start the exclusion on the device.

The successful exclusion is displayed in the app or at the gateway.

Press the Link button once to wake up the device. It then establishes a connection to the Z-Wave gateway and transmits the current status.

Factory reset Z-Wave Button

Press the Link button 3 times quickly (within 1.5 seconds).
Press quickly (within 1 second)
a fourth time and press and hold the Link button for at least 5 seconds.
The button is now reset to factory settings.

Please use this procedure only when the network primary controller is missing or otherwise inoperable.
If the device is set to factory default, the status is set to "not included" and the association settings and possible configurations are reset to default.

Please note that this is a user manual Z-Wave Button from ABUS is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Button and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.