Z-Wave Door-/Window Sensor (PLMK10000) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Z-Wave Door-/Window Sensor (PLMK10000)from ABUS. To view other Z-Wave products and manuals from ABUS follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


ABUS Z-Wave Door-/Window Sensor
SKU Code
The Z-Wave Door- / Window Sensor detects the opening of windows and doors and informs your smart home gateway. Thanks to an overall height of only 3 mm, installation in door or window frames is possible – simply by adhesive mounting. When closed, the detector cannot be seen from the outside or inside.
Version #
HW: 3 FW: 4.04:00.03 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, Z-Wave Door-/Window Sensor supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


ABUS describes Z-Wave Door-/Window Sensor as having the following features:

  • Battery Quantity
  • Outdoor Use
  • Color
  • Battery powered using Built in 3.0V LiMnO2 batteries
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

1.) Place the round magnet on the upper rounded edge and remove it as soon as the LED Lights up.
2.) Repeat this procedure 3 times within 10 seconds

1.) Activate the inlcusion mode at your Gateway
2.) keep the device within range of the gateway and remove both magnets from the device.
3.) Successfull inclusion is displayed at the Gateway (or app) and the status LED of device lights up for several seconds
4.) If the inclusion was not successfull, repeat it again.

1.) Activate the exclusion mode at the Gateway
2.) Place the round magnet on he upper rounded edge of device and remove it as soon as the LED lights up. Repeat this 3 times within 10 seconds.
3.) Successfull exclusion is displayed in the App or at the gateway and the status LED on device lights up one time.
4.) Repeat the exclusion process again if it was unsuccessfull.

Factory reset Z-Wave Door-/Window Sensor

1.) Place the round magnet on the upper rounded edge and remove it as soon as the LED lights up. Repeat the procedure 3 x ... and leave the magnet on the rounded edge for 10 seconds at the third time.
2.) The LED now flashes 1 x long to confirm the process.
The unit is now reset to factory settings.

This procedure should only be used if the primary gateway is not capable of acting. If the device is set to factory default, the status is set to "not included", the association settings and possible configurations are reset to default.

SmartStart location

SmartStart QR code's location as follows: chapter 1.6 DSK Code (Page 7) ... "The DSK Code (Device-Specific-Key) is the device-specific key of your device and is required for Security Inclusion (teach-in) via S2 to the gateway. The first 5 digits of the DSK code can be found on the rear side of the product. Please enter them in the inclusion process when prompted. Alternatively, you can enter the entire DSK code found on the enclosed DSK card to the gateway via QR Code Scan. Please keep the DSK card in a safe place!"

Please note that this is a user manual Z-Wave Door-/Window Sensor from ABUS is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Door-/Window Sensor and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.