The following is an overview of the user manual for the Z-Wave product Z-Wave Dual Pet PIR (PLBW10000)from ABUS. To view other Z-Wave products and manuals from ABUS follow that link.
Overview
It uses Passive Infrared (PIR) technology to detect movement in a defined area by detecting the changes in thermal radiation caused by the moving body inside or outside the detection zone. With the dual PIR sensor (dual-lens technology), the sensor hides pets up to approx. 38kg, so that your pet can move freely without triggering the sensor.
When the motion detector is triggered, an alarm signal is sent to the Z-Wave controller. The indicator LED lights up when motion is detected.
Integrated temperature and humidity sensor
At periodic intervals, the unit automatically sends the measured temperature and humidity value to the Z-Wave controller or on request of the Z-Wave controller.
Tamper protection between the device and wall bracket
When the housing is opened, the tamper switch is triggered and the device sends a tamper alarm to the Z-Wave controller. The tamper contact must remain pressed for three seconds to reset the tamper alarm.
Security
As a Z-Wave Plus certified product, Z-Wave Dual Pet PIR supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
ABUS describes Z-Wave Dual Pet PIR as having the following features:
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: 1.2 Z-Wave QR Code DSK Sticker for S2 Inclusion is located on the backside of the bracket
1.6 The DSK code (Device-Specific Key) is the device-specific key of your device and is required for secure teach-in (inclusion) via S2 on the Z-Wave controller. The first 5 digits of the DSK code can be found on the QR Code sticker on the backside of the bracket of the product.
Activate the inclusion mode (teach-in mode) on the Z-Wave controller. (please refer to the Z-Wave controller manual for more details)
Press the "+" button (Add / Inclusion) in your Z-Wave app and follow the instructions to set the Z-Wave controller to inclusion mode.
Keep the device within reach of the Z-Wave controller.
Remove the safety strip from the battery compartment. We recommend the exclusive use of the original GP battery from the scope of delivery.
The device supports automatic inclusion, i.e. it automatically goes into inclusion mode when it is powered and not yet connected to a Z-Wave controller. The LED starts flashing.
Alternative/manual inclusion:
If you have already inserted the batteries, press the Link button 3 times quickly (within 1.5 seconds) to start the inclusion process.
Activate the exclusion mode (teach-out mode) on the Z-Wave controller. (please refer to the Z-Wave controller manual for more details)
Press the "-" button (Remove / Exclusion) in your Z-Wave app and follow the instructions to set the Z-Wave controller to Exclusion mode.
Press the Link button 3 times quickly (within 1.5 seconds) to start the exclusion on the device.
Press the Link button once to wake up the device. It then establishes a connection to the Z-Wave controller and transmits the current Status.
Factory reset Z-Wave Dual Pet PIR
Press the Link button 3 times quickly (within 1.5 seconds).
Press quickly (within 1 second)
a fourth time and press and hold the Link button for at least 5 seconds.
The device is now reset to factory settings.
Hint:
This procedure should only be used if the primary network controller is not capable of acting.
If the device is set to factory default, the status is set to "not included" and the association settings and possible configurations are reset to default.
Please note that this is a user manual Z-Wave Dual Pet PIR from ABUS is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Dual Pet PIR and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.