Interlogix Simon XT/i Radio Module (ADC-200H-EVD) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Interlogix Simon XT/i Radio Module (ADC-200H-EVD)from Alarm.com. To view other Z-Wave products and manuals from Alarm.com follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Alarm.com Interlogix Simon XT/i Radio Module
SKU Code
ADC-200H-EVD
Description
The Alarm.com Interlogix Simon XT/i Radio Module is an add-on module that attaches inside of an Interlogix Simon XT or XTi security panel. It communicates between the security panel and the Alarm.com cloud service via a cellular network. A user is able to remotely control the security panel and its associated Alarm.com Interactive Services (including Z-Wave devices) via a web application or mobile app.
Version #
HW: 115 FW: 4.32:03.04 was the version certified
Certification #
ZC10-16045033
Certified
2016-03-07T09:53:31.1256
Z-Wave Version
6.51.06

Security

As a Z-Wave Plus certified product, Interlogix Simon XT/i Radio Module supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    Alarm.com describes Interlogix Simon XT/i Radio Module as having the following features:

    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    Factory reset Interlogix Simon XT/i Radio Module

    Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

    1.3 Reset Alarm.com Module to default state
    NOTE: This function will forcibly clear the Alarm.com module’s Z-Wave node identification and will also remove all network information from the module.
    1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site
    2. Navigate to the Equipment page.
    3. Click the “emPower Devices” tab.
    4. Open the “Advanced Z-Wave Commands” menu by clicking the button below the Equipment List.
    5. Towards the bottom next to the “Equipment List Label” text click on the “Reset To Factory Default” button
    6. Allow 3 minutes for the associated commands to go through and for the module to act on them

    Support for the Wake Up command class is enabled using Alarm.com’s rules engine. This requires a series of rules pushed from the cloud when Alarm.com detects that a Wake Up device has been added to the Alarm.com Module.
     For this reason Wake Up notifications will only be handled properly by the Alarm.com module after any locally added Wake Up devices have been reported to the backend. This can take up to 15 minutes, but can be accelerated by using Remote Add or by requesting a Z-Wave Equipment List from the Alarm.com backend.

    1.1 Adding devices to the Alarm.com Module’s Z-Wave Network
    NOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com Module will have network information replicated over to them.
    1. Using Mobiletech
    a. Install the MobileTech App (if not already done) and select the customer of interest.
    b. Move all Z-Wave devices to their final location on the property.
    c. Navigate to the Equipment List page.
    d. Select emPower Management.
    e. Select Add Z-Wave Devices
    f. Wait for the bolded message: Checking for new devices on the network
    g. Trigger a device to add it to the network.
    h. When a device is added successfully, it will show up on this screen following a 30 second delay.
    i. Continue triggering devices. You may add many devices to the network without reentering Add Mode.
    2. Using the Dealer Website
    a. Navigate to the Equipment page.
    b. Click the emPower Devices tab.
    c. Open the Advanced Z-Wave Commands menu below the Equipment List.
    d. Click Add Z-Wave Devices.
    e. Wait for the bolded message: Checking for new devices on the network.
    f. Trigger a device to add it to the network.
    g. When a device is added successfully, it will show up on this screen following a 30 second delay.
    h. Continue triggering devices. You may add many devices to the network without reentering Add Mode.
    3. Using the Simon XTi Panel
    a. Enter System Programming.
    b. Select Interactive Services.
    c. Select Z-Wave.
    d. Select Add Device.
    e. Trigger a device to add it to the network.
    f. When a device is added successfully, the panel will beep.
    g. You will need to re-enter Add Mode before triggering the next device.

    List page.
    d. Select emPower Management.
    e. Select Delete Z-Wave Devices
    f. Wait for the bolded message: Checking for deleted devices on the network
    g. Trigger a device to remove it from the network.
    h. When a device is deleted successfully and its network information is erased, it will show up on this screen following a 30 second delay.
    i. Continue triggering devices. You may delete many devices to the network without reentering Delete Mode.
    2. Using the Dealer Website
    a. Move all Z-Wave devices you plan to delete close to the Alarm.com Module.
    b. Navigate to the Equipment page.
    c. Click the emPower Devices tab.
    d. Open the Advanced Z-Wave Commands menu below the Equipment List.
    e. Click Delete Z-Wave Devices.
    f. Wait for the bolded message: Checking for deleted devices on the network.
    g. Trigger a device to remove it from the network.
    h. When a device is deleted successfully and its network information is erased, it will show up on this screen following a 30 second delay.
    i. Continue triggering devices. You may delete many devices to the network without reentering Delete Mode.
    3. Using the Simon XTi Panel
    a. Enter System Programming.
    b. Select Interactive Services.
    c. Select Z-Wave.
    d. Select Delete Device.
    e. Trigger a device to remove it from the network.
    f. When a device is deleted successfully and its network information is erased, the panel will beep.
    g. You will need to re-enter Delete Mode before triggering the next device.

    1.4 Learning the Alarm.com Module into another Z-Wave network
    1. Learning in the Alarm.com Module using the Dealer Site
    a. Log in to the Alarm.com Dealer Site
    b. Select the customer whose node you wish to remove
    c. Navigate to the page to allow sending generic commands. This can be found in the AirFX Remote Toolkit or by navigating to https://alarmadmin.alarm.com/Support/Commands/GenericCommand.aspx
    d. Place a controller on the existing network into add mode
    e. Send the generic command 5B10030101 to the module, once received it will cause the Alarm.com Module to learn into the existing Z-Wave network and will allow it to cause all relevant network information to be copied over from the controller that was put into add mode.
    2. Learning in the Alarm.com Module from the Local UI on the XTi Panel
    a. Ensure that no Z-Wave devices are currently learned into the module. A Z-Wave Factory Reset will make sure of this.
    b. Put a controller on the existing network into add mode
    c. Navigate the menus to the Interactive Services Menu and then select “Z-Wave” followed by “Replicate Mode”
    d. This will cause the Alarm.com Module to learn into the existing Z-Wave network and will allow it to cause all relevant network information to be copied over from the controller that was put into add mode.

    Please note that this is a user manual Interlogix Simon XT/i Radio Module from Alarm.com is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Interlogix Simon XT/i Radio Module and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.