Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Smart Door Lock (ADSL-1001) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Smart Door Lock (ADSL-1001)from AMADAS. To view other Z-Wave products and manuals from AMADAS follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
AMADAS Smart Door Lock
SKU Code
ADSL-1001
Description
AMADAS offers various smart functions via smartphone app including smart activity log/management, smart security detecting door open, smart temperature sensor, etc. AMADAS is a super simple DIY smart lock that can be installed on almost all types of doors in any thickness, in-door/outdoor, and any materials - wooden, chassis, steel doors. It is offered in tubular and mortise lock types with high adjustability compatible with various door backset length. With a low power motor structure, it only requires two AA batteries, unlike other locks which require four to eight batteries. Even when batteries run out, it works 100% thanks to an emergency recharge with a built-in solar cell via smartphone LED flashlight. The smart innovative lever design prevents water condensation caused by a temperature change that other electronic locks experience quite often. AMADAS lever direction can change easily to fit both right or left hand configured doors.
Version #
HW: 1 FW: 1.18:01.02 was the version certified
Certification #
ZC10-18026009
Certified
2018-02-13T07:02:27.685819
Z-Wave Version
6.51.10

Security

As a Z-Wave Plus certified product, Smart Door Lock supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    AMADAS describes Smart Door Lock as having the following features:

    • Color
    • Battery powered using LR06 AA batteries
    • Sensors
    • Door Lock Type
    • Battery Quantity
    • Firmware updatable via a compatible Z-Wave gateway
    • Outdoor Use
    • Supported Notification Types
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    - Z-Wave inclusion
    i. Press “Z-Wave Settings” button in the inner side for 3 seconds. (toggle status)
    ii. Then “Blue LED” will turn on.
    iii. When the inclusion is complete, the led is turned off and the beep sounds. Please wait.
    * Beep : Success (Beep), Fail (Beep~)
    * The inclusion results can be found in the controller or in your app.

    - Z-Wave exclusion
    i. Press “Z-Wave Settings” button in the inner side for 3 seconds. (toggle status)
    ii. Then “Blue LED” will turn on.
    iii. When the exclusion is completed, the led is turned off and the beep sounds. Please wait.
    * Beep : Success (Beep Beep), Fail (Beep~)
    * The exclusion results can be found in the controller or in your app.

    Factory reset Smart Door Lock

    - Factory default setting
    i. Press “Settings, Input” button in the inner side for 3 seconds.
    ii. Press “④ - Reset” button in the outer side.
    iii. Enter “1004” and press the “*” button.
    * All door lock setting information is initialized.

    - Z-Wave device reset locally
    i. Press “Z-Wave Settings” button in the inner side 3 times within 1.5 seconds.
    ii. Then “White LED” will turn on.
    iii. When the “network reset locally” is complete, the led is turned off. Please wait.
    * Beep : Success (Ring), Fail (Beep~)
    * Z-Wave network information is initialized.
    * Please use this procedure only when the network primary controller is missing or otherwise inoperable.

    - Through the Z-Wave network generates an order, the product will receive the wakeup call and starts to operate

    - The product will receive the wakeup call when the buttons on the outer lever are touched (pushed) to open the door.

    - The product will receive the wakeup call when the buttons on the inner lever are pushed for doorlock setting.

    Please note that this is a user manual Smart Door Lock from AMADAS is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Smart Door Lock and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.