The following is an overview of the user manual for the Z-Wave product PIR Motion Sensor (T8341-JP)from Axis Communications . To view other Z-Wave products and manuals from Axis follow that link.
Overview
Security
As a Z-Wave Plus certified product, PIR Motion Sensor supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Axis describes PIR Motion Sensor as having the following features:
- Battery powered using CR123A batteries
- Color
- Supported Notification Types
- Battery Quantity
- Firmware updatable via a compatible Z-Wave gateway
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Factory reset PIR Motion Sensor
Factory Reset (This procedure should only be used when the controller is inoperable.)
1. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode.
2. Within 1 second of step 1, press the tamper switch again and hold until LED is off (about 5 seconds).
3. Node ID is excluded. The device reverts to 2-second on, 2-second off factory default state and will be in auto-inclusion mode for 4 minutes.
Manual exclusion
Note
For more details see the installation guide
1. Detach the battery cover.
2. Press the tamper switch 3 times within 1.5 seconds to put the unit into learning (inclusion/exclusion) mode.
3. The exclusion process should be completed when the LED stops blinking
4. Refit the battery cover.
Wakeup Command Class
After it has been included into a Z-Wave network, the detector will go to sleep but will send a Wakeup
Notification Command periodically at preset period to the controller. The Motion detector will stay awake
for 10 seconds at least and then go back to sleep to conserve battery life.
The time interval between Wakeup Notification Commands can be set in the Wakeup Command Class
based on the range values below:
Minimum Wake Up Interval 600s (10 minutes)
Maximum Wake Up Interval 86400s (1 day)
Default Wake Up Interval 14400s (4 hours)
Wake Up Interval Step Seconds 600s (10 minutes)
The user can set a detecting percentage of lux level which determines when the light sensor will be activated. If percentage of lux level of ambient illumination falls below this percentage, and a person moves across or within the protected area, the detector will emit Z-Wave ON Command (i.e. Basic Set Command (Value = Basic Set Level)) to controller and activate connected modules and lighting. Percentage can be set between 1% to 100%.
Auto inclusion
The motion sensor supports the auto inclusion feature where it will automatically enter Inclusion mode when first powered up.
This will also apply when powered up after a factory reset.
1. Use a screwdriver to detach the rear cover.
2. Put the AXIS M6505 camera (Z-Wave controller) into inclusion mode.
3. Insert 1 CR123 3V batteries into the battery compartment with the correct polarity. The LED on the device should turn ON
4. The inclusion process should be completed when the LED stops blinking
5. Perform test before you refit the rear cover.
Manual inclusion
You can also choose to manually add the Z-Wave device to a control device. Please follow the steps described below.
Note
For best results, exclude the device before starting the inclusion process. For more details see the installation guide
1. Press the tamper switch 3 times within 1.5 seconds to put the unit into learning (inclusion/exclusion) mode.
2. The inclusion process should be completed when the LED stops blinking
3. Perform a test before you refit the cover.
Please note that this is a user manual PIR Motion Sensor from Axis Communications is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have PIR Motion Sensor and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.