The following is an overview of the user manual for the Z-Wave product Wireless Water Detector 700 (WWDZWU)from Custos. To view other Z-Wave products and manuals from Custos follow that link.
Overview
Security
As a Z-Wave Plus certified product, Wireless Water Detector 700 supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Custos describes Wireless Water Detector 700 as having the following features:
- Outdoor Use
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
1. SmartStart:
- To enable SmartStart, below methods can be used, please also refer to Gateway’s user manual
i. Scan the Z-Wave QR Code or entering PIN Code or DSK String into S2 Enabled Gateway, please refer to item 16.11 SmartStart Labeling,
. Re-install the battery then SmartStart will be enabled automatically,
2. Classic Inclusion / Add Device:
- To enable Classic Inclusion:
i. Set your Z-Wave Gateway into Inclusion Mode / Add Device processing.
ii. Trigger Built-in Water Leak Sensor for 2 Seconds.
iii. 2 x Buzzer Sound and 2 GREEN LED ON UI to confirm enter into Inclusion Mode
iv. YELLOW LED will be flashing when Inclusion is processing.
Factory reset Wireless Water Detector 700
To perform Factory Default Reset as following steps – Only works in Mesh Network Mode
. Shaking Custos WWD in Vertical / Horizontal to wake up it until get 1x Buzzer Sound & 1x GREEN LED ON,
. Then stop shaking it, left WWD on the table in Horizontal position as Figure 12A,
. Wait for Position Recognition confirmation UI with Buzzer Sounds & GREEN LED flashing 2 times “Event success UI”,
. While GREEN & RED LED are flashing alternative for Gesture Recognition then roll Custos WWD in one complete turn “360°”and stick
close to table surface as Figure 12B,
. Wait for Gesture Recognition configuration UI with Buzzer Sounds & GREEN LED flashing 2 times “Event success UI”,
. Then WWD will perform soft reset after GREEN LED is flashing for 2 seconds,
. After soft reset with RED LED & Buzzer Sound x1 to finished Factory Default Reset action then SmartStart also will be activated.
None
SmartStart location
SmartStart QR code's location as follows: 1. The QR code of DSK is printed on the product itself;
2. The full DSK & QR code of packing label can be are printed on found outside of giftbox
Shaking Custos WWD in Vertical/Horizontal to wakeup it until get 1xBuzzer Sound & 1xGREENLEDON,
1. Trigger Built-in Water Leak Sensor - Only works in Standalone Mode
. Set your Z-Wave Gateway into Exclusion Mode / Remove Device processing,
. Trigger Built-in Water Leak Sensor for 2 Seconds,
2. Use Gesture Recognition – Only works in Mesh Network Mode
. Set your Z-Wave Gateway into Exclusion Mode / Remove Device processing,
. Shaking Custos WWD in Vertical / Horizontal to wakeup it until get 1x Buzzer Sound & 1x GREEN LED ON,
. Then stop shaking it, left WWD on the table in Horizontal position as Figure 11A,
. Wait for Position Recognition confirmation UI with Buzzer Sounds & GREEN LED flashing 2 times “Event successUI”,
. While GREEN & RED LEDs are flashing alternative for Gesture Recognition then turn Custos WWD from Horizontal to Vertical position
“90°”and stick close to table surface as Figure 11B,
. Wait for Gesture Recognition configuration UI with Buzzer Sounds & GREEN LED flashing 2 times “Event success UI” for completion
Please note that this is a user manual Wireless Water Detector 700 from Custos is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Wireless Water Detector 700 and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.