The following is an overview of the user manual for the Z-Wave product Door/Window Sensor Pro (DMDP1)from Dome. To view other Z-Wave products and manuals from Dome follow that link.
Overview
• Z-Wave Plus Certified
• S0 Security-Enabled*
• Built-In Temperature Sensor
• Up to 250’ range
• Ten-Year Battery Life
• LED Signal Strength Indication
• 1.25” Max distance between sensor & magnet
• Ultra-Narrow (1/4”) Magnet for Placement Between Door and Casing
• Monitor doors, windows, medicine cabinets, drawers, garage doors, and many other openings
Security
As a Z-Wave Plus certified product, Door/Window Sensor Pro supports Z-Wave S2 security. The following security modes are directly supported:
Features
Dome describes Door/Window Sensor Pro as having the following features:
- Color
- Battery Quantity
- Battery powered using 3.7V 14505 batteries
- Firmware updatable via a compatible Z-Wave gateway
- Sensors
- Supported Notification Types
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Follow the instructions for your Z-Wave Certified Controller to enter exclusion mode. When prompted by the controller:
Remove the SENSOR COVER and the LED Indicator will start blinking red.
Press the Button quickly 3 times in a row.
The LED Indicator will flash green three times indicating exclusion/disconnection and will then continue flashing red (indicating tamper) until the cover is replaced.
New Installation
1. For proper inclusion, bring the Door/Window Sensor Pro to the final location where it will be used*.
2. Follow the instructions for your Z-Wave controller to enter inclusion mode.
3. Remove the Battery Tab protruding from the Battery Tab Slit.
4. The device will automatically enter inclusion mode for two minutes and the LED Indicator will alternate between green and red.
Upon successful inclusion the LED Indicator will flash green three times then stop blinking.
Re-Installation
1. For proper inclusion, bring the Door/Window Sensor Pro to the final location where it will be used*.
2. Follow the instructions for your Z-Wave controller to enter inclusion mode.
3. Remove the Sensor Cover and the LED Indicator will start blinking yellow.
4. Press the Button quickly 3 times in a row.
5. The device will enter inclusion mode for two minutes and the LED Indicator will alternate between green and red.
After successful inclusion, the LED Indicator will flash green three times then blink red until the cover is replaced.
*For non Z-Wave Plus networks, please consult the owner’s manual for your primary controller to determine the best method and location for adding the Door/Window Sensor Pro to your Z-Wave network.
Factory reset Door/Window Sensor Pro
If needed, the Door/Window Sensor Pro can be reset locally by following these steps. Only do this if your Z-Wave controller is missing or otherwise unreachable. Beware that resetting your device will disconnect it from the system:
1. Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
2. Wait for 5 seconds.
3. Move the Magnet and Sensor Base in and out of the closed position 6 times.
4. The LED Indicator will light up red for five seconds when reset successfully.
The Door/Window Sensor’s memory will be erased to factory settings.
Because the Door/Window Sensor Pro is a battery powered device, it wakes up on regular intervals to give battery and other status updates to the controller, as well as to accept configuration settings from the controller. This helps to extend the battery life. The Sensor Cover holds down the Button when installed, and the device can be forced to wake up to submit reports or accept new settings immediately by simply removing the Sensor Cover and then replacing it after. If the device is already included in a system, the LED Indicator will flash Red until the cover is closed.
Please note that this is a user manual Door/Window Sensor Pro from Dome is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Door/Window Sensor Pro and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.