Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Mouser (DMMZ1) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Mouser (DMMZ1)from Dome. To view other Z-Wave products and manuals from Dome follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Dome Mouser
SKU Code
DMMZ1
Description
The Dome™ Home Automation DMMZ1 Mouser is a powerful rodent electric trap with Z-Wave technology built-in. It kills mice, rats and other rodents quickly, cleanly and humanely with a powerful jolt of electricity. Simply set bait, turn on and place in desired location. When connected to Z-Wave Certified Hub, once the trap is full, it sends out a notification to your smarthome system. You can easily dispose of Mouser’s contents without ever having to touch them. Use the top handle and tip to dispose of caught rodents. Specially designed removable and washable bait tray will allow you to easily replace the bait and set it back up. It operates on 4 AA batteries (not included) and is optimised to last over 50 uses. Mouser features extra-long Z-Wave wireless range (up to 150 ft) and Dome™ DMMZ1 Mouser comes with a 1-year limited warranty. Measurements in inches: 8.75 x 4.5 x 5. Dome™ Home Automation Z-Wave devices give your family peace of mind and security you can count on. With Dome™, you’re always connected and always covered.
• Humanely kills mice, rats and other rodents with a powerful electric shock and sends an alert to your smarthome system when the trap needs to be emptied
• Easy to use: set bait, turn on and place in desired location
Touch free: hold handle and tip to dispose of contents, then set it again
• Up to 150-foot Z-Wave range. Operating Temperature: 32°F - 112°F. Powered by 4 AA batteries (not included) enabling it to be triggered over 50 times
• Z-Wave Plus Certified. Works as a stand alone electronic mouse trap but requires a Z-Wave Certified Hub for notification functionality
• Tested to work with SmartThings, Vera, Staples Connect, HomeSeer, Nexia, Piper, URC, Harmony. Not supported by Wink, DSC, ADT Pulse, 2Gig, Napco, Interlogix, Honeywell (Dome is not associated with listed brands)
Version #
HW: 82 FW: 3.16 was the version certified
Certification #
ZC10-16095211
Certified
2016-09-06T11:29:40.7486
Z-Wave Version
6.51.06

Security

As a Z-Wave Plus certified product, Mouser supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    Dome describes Mouser as having the following features:

    • Battery Quantity
    • Battery powered using 1.5V AA Size batteries
    • Color
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    Follow the instructions for your Z-Wave Certified controller to enter inclusion mode. When prompted by the controller:
    1. Bring the Mouser to within 10’ of your Z-Wave controller for the inclusion process. After successful pairing, the device can be brought to the desired location.
    2. Remove top cover by sliding it back and lifting up.
    3. Insert batteries.
    4. Press the CONNECT BUTTON quickly 3 times in a row.
    5. The LED INDICATOR will flash five times indicating inclusion

    Follow the instructions for your Z-Wave Certified controller to enter exclusion mode.
    When prompted by the controller:
    1. Remove top cover by sliding it back and lifting up.
    2. Press the CONNECT BUTTON quickly 3 times in a row.
    The LED INDICATOR will flash five times indicating exclusion/disconnection.

    If needed, the Mouser can be reset locally by following these steps. Only do this when your Z-Wave controller is disconnected or otherwise unreachable. Beware that resetting your device will disconnect it from the system:
    1. Remove the TOP COVER and confirm that your Mouser is powered up.
    2. Press and hold the CONNECT BUTTON for at least 10 seconds then release. A flashing LED INDICATOR indicates a successful factory reset.
    3. The Mouser’s memory will be erased to factory settings.

    Factory reset Mouser

    If needed, the Mouser can be reset locally by following these steps. Only do this when your Z-Wave controller is disconnected or otherwise unreachable. Beware that resetting your device will disconnect it from the system:
    1. Remove the TOP COVER and confirm that your Mouser is powered up.
    2. Press and hold the CONNECT BUTTON for at least 10 seconds then release. A flashing LED INDICATOR indicates a successful factory reset.
    3. The Mouser’s memory will be erased to factory settings.

    Please note that this is a user manual Mouser from Dome is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Mouser and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.