Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

On/Off Plug-In Switch (DMOF1) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product On/Off Plug-In Switch (DMOF1)from Dome. To view other Z-Wave products and manuals from Dome follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Dome On/Off Plug-In Switch
SKU Code
DMOF1
Description
The Dome™ Home Automation DMOF1 On/Off Plug is designed to give you control over small appliances from your smart device wherever you are. Conserve energy and save money always knowing how much power is used by every monitored appliance. Plug in your lamp and have it turn on/off on demand or according to preset schedule (Z-Wave Certified Hub required). Also great for humidifiers, dehumidifiers, air conditioners, space heaters, fans and holiday lights. It never blocks the other side of your duplex receptacle with the ergonomic design. Extra-long Z-Wave wireless range (up to 150 ft) allows you to place it where it’s needed without worrying if the signal is reaching your Z-Wave Hub. It also acts as a Z-Wave range extender. Dome™ DMOF1 On/Off Plug comes with a 1-year limited warranty. Measurements in inches: 1.625 x 1.625 x 2. Dome™ Home Automation system gives your family peace of mind and security you can count on. With Dome™, you’re always connected and always covered.

• Used to turn On/Off lamps and small appliances for up to 13 Amps (1,560 Watts). Monitors energy consumption of attached device and shuts down in case of overload with build-in protection circuit
• Ergonomic design allows it to only occupy single side of electrical duplex leaving the second outlet fully accessible. It doubles as Z-Wave signal extender
• Up to 150-foot range. Operating Temperature: 32°F - 112°F
• Z-Wave Plus Certified. Requires a Z-Wave Certified Hub to operate
• Tested to work with SmartThings, Vera, Staples Connect, HomeSeer, Nexia, Piper, URC, Harmony. Not supported by Wink, DSC, ADT Pulse, 2Gig, Napco, Interlogix, Honeywell (Dome is not associated with listed brands)
Version #
HW: 65 FW: 3.70 was the version certified
Certification #
ZC10-16095213
Certified
2016-09-06T11:19:05.2358
Z-Wave Version
6.51.06

Security

As a Z-Wave Plus certified product, On/Off Plug-In Switch supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    Dome describes On/Off Plug-In Switch as having the following features:

    • Color
    • Switch Load Capacity Current
    • Switch Load Capacity Watts
    • Supported Meter Type
    • Switch Type
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    Follow the instructions for your Z-Wave certified Controller to enter inclusion mode.
    When prompted by the Controller:
    1. For proper inclusion, bring the On/Off Plug-In Switch to within 10 feet of your Controller and plug it in. After inclusion, the device can be moved to any desired location.
    2. Press the Connect Button quickly 3 times in a row.
    The LED Indicator will flash five times indicating inclusion.

    Follow the instructions for your Z-Wave certified Controller to enter exclusion mode.When prompted by the Controller:
    1. Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
    2. Press the Connect Button quickly 3 times in a row.
    The LED Indicator will flash five times indicating exclusion/disconnection.

    Factory reset On/Off Plug-In Switch

    To disconnect from the Z-Wave Network and restore factory default settings:
    1. Plug in the On/Off Plug-In Switch.
    2. Hold the Connect Button for 10 seconds until the LED Indicator blinks once, then release the button.
    Only do this if the controller is disconnected or otherwise unreachable!

    Please note that this is a user manual On/Off Plug-In Switch from Dome is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have On/Off Plug-In Switch and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.