System Controller (EL-SC-100) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product System Controller (EL-SC-100)from Elan. To view other Z-Wave products and manuals from Elan follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Elan System Controller
SKU Code
EL-SC-100
Description
A Smart Home means enjoying the maximum comfort and convenience technology can provide. Connect all of your devices under one platform using Z-Wave, IP, RS-232, or IR control. The award-winning ELAN user experience sets us apart and gives you full and easy control of your connected smart home and entertainment system.
Version #
HW: 1 FW: 7.13:02.03 was the version certified
Certification #
ZC12-20120148
Certified
2020-11-05T13:41:03.224602
Z-Wave Version
7.13.1

Security

As a Z-Wave Plus certified product, System Controller supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Access Control
  • S2 Authenticated
  • S2 Unauthenticated

Features

Elan describes System Controller as having the following features:

  • Firmware updatable via a compatible Z-Wave gateway
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: Products are professionally installed. During configuration the UI will present the DSK information.

1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or Input/Output Tabs in Configurator
2. Set Management View: Network Management
3. Set Network Action: Include
4. Put device in Inclusion/Learn mode per manufacturer instruction

Execute (button to right of Network action)

1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or Input/Output Tabs in Configurator
2. Management View: Network Management
3. Network Action: Exclude
4. Put device in Exclusion/Learn mode per manufacturer instruction
5. Execute (button to right of Network action)

1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or Input/Output Tabs in Configurator
2. Management View: Network Provisioning.
3. Network Action: Remove Device – This action removes the device only form the provisioning list & not from Z-wave network.
4. Network Action: Clear List – This action removes all the devices only form the provisioning list & not from Z-wave network.

Replication of network information from the controller to another controller is not supported.

1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or Input/Output Tabs in Configurator
2. Management View: Network Management
3. Network Action: Learn
4. Put other controller in Add/Include mode per manufacturer instruction
5. Execute (button to right of Network action)

1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or Input/Output Tabs in Configurator
2. Management View: Network Management
3. Node Action: Request Info
4. Select desired Node ID in the Devices list
5. Execute (button to right of Node action)

Factory reset System Controller

1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or Input/Output Tabs in Configurator
2. Management View: Network Management
3. Network Action: Reset
4. Execute (button to right of Network action)

SmartStart installation

1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or Input/Output Tabs in Configurator
2. Management View: Network Provisioning.
3. Refer device documentation / manufacturer instruction for Z-wave DSK of the device.
4. Put device full DSK string in Device DSK text box & click Append.
5. Click on “ Add device to List “ button.
6. Click on “Discover Devices button” at the bottom.
7. Power on the end device or any other mechanism to start smart start in the device to be added into SC100 network. Refer manufacturer instruction.

Please note that this is a user manual System Controller from Elan is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have System Controller and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.