Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Plug-in Smart Dimmer (Dual Plug with Simultaneous Control) (55251/ ZW3107) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Plug-in Smart Dimmer (Dual Plug with Simultaneous Control) (55251/ ZW3107)from Enbrighten. To view other Z-Wave products and manuals from Enbrighten follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Plug-in Smart Dimmer (Dual Plug with Simultaneous Control)
SKU Code
55251/ ZW3107
Description
Transform any home into a smart home with the Enbrighten Z-Wave Smart Lighting Control Lamp Module with Dimmer Control. The lamp module enables wireless control of on/off and dim functions for standard incandescent table and floor lamps, as well as dimmable fluorescent, LED and CFL fixtures and more! Use the dimmer control to customize the lighting output and create the perfect ambiance for any room. The space-saving horizontal module plugs into a standard wall receptacle without blocking the second outlet or obstructing placement of furniture. It provides simultaneously controlled Z-Wave enabled outlets for the lamps you would like to control and other electrical appliances. Take control of your home lighting with Enbrighten Z-Wave Smart Lighting Controls!
Version #
HW: 255 FW: 5.50 was the version certified
Certification #
ZC10-20086965
Certified
2020-08-14T13:12:25.05602
Z-Wave Version
6.82.00

Security

As a Z-Wave Plus certified product, Plug-in Smart Dimmer (Dual Plug with Simultaneous Control) supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated

Features

Enbrighten describes Plug-in Smart Dimmer (Dual Plug with Simultaneous Control) as having the following features:

  • Firmware updatable via a compatible Z-Wave gateway
  • Switch Load Capacity Current
  • Switch Load Capacity Watts
  • Switch Type
  • Z-Wave Scene Type
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1).

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your smart dimmer, single press and release the manual/program button on
the smart dimmer.

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave
network.
2. Once the controller is ready to remove your device, press and release the manual/program button on the smart dimmer.

Factory reset Plug-in Smart Dimmer (Dual Plug with Simultaneous Control)

1. If plugged in, unplug the dimmer from the receptacle.
2. Press and hold the top button for at least three seconds while you plug the dimmer into a receptacle.
3. The LED will flash five times when completed successfully.

Please note that this is a user manual Plug-in Smart Dimmer (Dual Plug with Simultaneous Control) from Enbrighten is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Plug-in Smart Dimmer (Dual Plug with Simultaneous Control) and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.