The following is an overview of the user manual for the Z-Wave product Z-Wave Plus Extender (ES800ZWP_EU_Mxx)from Essence Security. To view other Z-Wave products and manuals from Essence Security follow that link.
Overview
- Door locks
- On/Off switches
- Dimmers
- Thermostats
- Power strips
- Multi-channel devices
- Multi-colored RGBW LED bulbs
- Multi-input/ multi-output devices
- Glass break detector
- Garage door controller
Security
As a Z-Wave Plus certified product, Z-Wave Plus Extender supports Z-Wave S2 security. The following security modes are directly supported:
Features
Essence Security describes Z-Wave Plus Extender as having the following features:
- Color
- Communications Connections
- Gateway Has Preferred Partners
- Switch Load Capacity Current
- Switch Load Capacity Volt-Ampere
- Supported Notification Types
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
After you install a Z-Wave Extender, you can add a Z-Wave device to WeR@Home™. Install the device
within 20 m (65.6 ft.) of the Z-Wave Extender. Use Z-Wave devices with repeater capabilities to extend
network range.
Before you begin, refer to the device’s documentation to learn the pairing process for the specific
device.
To add a Z-Wave device:
1. Log in to the WeR@Home™ app.
2. Tap . The main menu appears.
3. Tap DEVICES. The Devices screen appears.
4. Tap ""Add new device"". The Add New Devices screen appears displaying a list of the available device
types including the Z-Wave device types.
5. Select the type of Z-Wave device to be added. The Power your device window appears.
6. Position the Z-Wave device within 0.5 m (1.6 ft.) of the Z-Wave Extender.
7. Insert batteries into the device or connect to the nearest power outlet. The Step 1 of 2 pairing
screen appears.
You can remove a Z-Wave device from WeR@Home™ if the device is not needed, becomes
unresponsive, or becomes disconnected from the network.
To remove a Z-Wave device:
1. Log in to the WeR@Home™ app.Managing Your Z-Wave Devices
WeR@Home™ Z-Wave® User Guide 15
2. Tap . The main menu appears.
3. Tap DEVICES. The Devices screen appears.
4. Tap DELETE in the top right-hand corner of the screen.
5. Tap for the device that you want to remove. The Remove Z-Wave Device window appears.
6. Press the pairing button on the Z-Wave device, according the device’s documentation, and tap OK
in the window.
7. Tap OK in the top right-hand corner of the screen.
If you have an existing third-party Z-Wave network, WeR@Home™ can join the network. WeR@Home™ enters ""learn"" mode on the existing network to automatically copy the existing network's Smart Home network structure. When you join a Z-Wave network, you have access to the Z-Wave devices supported by WeR@Home™. The Z-Wave Plus Extender is assigned one of the following roles depending on the third-party controller capabilities:
Secondary (inclusion) - allowed to add or delete additional Z-Wave devices
Secondary –not allowed to add or delete additional Z-Wave devices
To join an existing third-party Z-Wave network:
1. Remove all Z-Wave devices from your WeR@Home™, except for your Z-Wave Plus Extender. Refer to 5.5 Removing a Z-Wave Device on page 15.
2. In the WeR@Home™ app, tap . The main menu appears.
3. Tap Devices. The Devices screen appears.
4. Tap for your Z-Wave Plus Extender. The Z-Wave Controller configuration screen appears.
5. Put the primary controller of the existing network into Add mode, according to the controller’s user manual.
6. Tap Join Existing Network. All Z-Wave devices are removed from WeR@Home™. WeR@Home™ copies the topology of the existing network and prompts you to enter the name for the existing network controller.
7. Enter the name for the existing network controller and tap OK.
Factory reset Z-Wave Plus Extender
Restoring factory settings returns your Z-Wave Plus Extender to its default settings and removes Z-Wave device definitions.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
To restore factory settings:
1. Tap . The main menu appears.
2. Tap Settings. The Settings menu appears.
Tap Z-Wave. The Z-Wave screen appears.
Tap Reset to Factory.
Please note that this is a user manual Z-Wave Plus Extender from Essence Security is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Plus Extender and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.