EZmultiPli (EZMultiPli) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product EZmultiPli (EZMultiPli)from Express Controls LLC. To view other Z-Wave products and manuals from Express Controls follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


SKU Code
Notify caregivers when a loved one does not get up at their usual time or gets up multiple times during the night. Easily installed in a kitchen, bathroom, bedroom or hallway - just plug it in! The wide angle motion sensor detects motion when placed at floor level in a normal wall outlet or at counter height in a kitchen or bath. Never needs batteries!

Receive an email or text when motion is detected or the temperature is dangerously low while you are away. Turn on lights and sirens automatically.

Save energy by automatically turning off lights in unoccupied rooms or hallways.

Set the color LED night light to inform you that your garage door is open, there is a severe weather alert or any indicator you can imagine!

Operates as a Z-Wave range extender utilizing fifth generation Z-Wave technology to enhance the reliability and speed of every device on a Z-Wave network.

Version 2.0 firmware adds AES-128 security S2 and SmartStart
Version #
HW: 3 FW: 2.01 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, EZmultiPli supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


Express Controls describes EZmultiPli as having the following features:

  • Firmware updatable via a compatible Z-Wave gateway
  • Supported Notification Types
  • Sensors
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

Configuration command class V3 is supported so the parameter Name, Min/Max/Default and a brief description can be obtained by interviewing the device.

When EZMultiPli is first plugged into the wall outlet, the LED should blink an aqua color. This indicates that it is not currently joined (or paired) to a Z-Wave network. If the LED is blinking white each time motion is detected, then it is already joined to a Z-Wave network. If the LED is blinking white you will need to exclude it from the other Z-Wave network before attempting to join a new one.
Follow the procedure of the Z-Wave primary controller to begin the exclusion process. Once the primary controller is ready to receive the exclusion command, press and release the push button on the side of EZMultiPli. The primary controller should give an indication that the reset process has completed. EZMultiPlis LED will blink aqua when it is ready to be added to a Z-Wave network.

SmartStart or press and release the button on the side.
LED blinks slowly light blue when not included.
Once included, the LED blinks white when motion is detected for about 5 minutes to test the motion detection area.

Factory reset EZmultiPli

Factory Reset
If the exclusion process above is not working or the controller EZMultiPli was originally joined to is lost or not available, the following process can be used to factory reset EZMultiPli.

Press and continue to hold the push button in for about 60 seconds. The LED will blink blue faster and faster and then shift to yellow and continue to blink faster and faster. Once the LED goes out, EZMultiPli is reset to the factory defaults and will blink aqua indicating it is ready to be added to a Z-Wave network.

Please note that this is a user manual EZmultiPli from Express Controls LLC is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have EZmultiPli and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.