The following is an overview of the user manual for the Z-Wave product Ezlo Plus (EzloPlus-US)from eZLO. To view other Z-Wave products and manuals from eZLO follow that link.
Overview
Features:
- Enables control of, or scene creation for, over 27,000 devices including lights, thermostats, door locks, sensors, and more, from multiple manufacturers
- Features Z-Wave™ SmartStart technology for faster device pairing, with S2 framework for enhanced security
- Uses local control for ultra-fast, “off the cloud” responsiveness
- Supports VistaCam indoor, outdoor, and doorbell cameras
- 7 days/week, 18 hrs/day tech support
Specifications:
- Z-Wave Plus™ (700 Series), Wi-Fi: 802.11 a/b/g/n/ac; 2.4 and 5GHz
- Hardware
Processor: 800MHz, Quad-Core Cortex-A7 ARM CPU
RAM: DDR3 512MB
Flash Memory: EMMC 4GB
- Dimensions:
(HxWxD) 4.17in(106mm) x 4.12in(104.66mm) x 1.45in(36.95mm)
- Power Supply:
Input: AC 100-240VAC, 50-60Hz
Output: DC 5V/2A
- Connectors:
1 USB Port 2.0, USB host
1 WAN Port 10/100 Ethernet
Security
As a Z-Wave Plus certified product, Ezlo Plus supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Access Control
- S2 Authenticated
- S2 Unauthenticated
Features
eZLO describes Ezlo Plus as having the following features:
- Thermostat Modes
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: The Z-Wave S2 DSK PIN 5 digits are located on the bottom of the Ezlo Plus.
You can also find the full DSK on the package box.
The Classic Inclusion process can be started via UI. From your Dashboard, go to Devices > tap on the + in the top right corner and select or search the name or type of device that you wish to pair with Ezlo Plus. To add a generic Z-Wave device, select the Generic Z-Wave device from the device categories. To add the device with your Ezlo Plus, if the device requires assembly read the manual, follow the assembly instructions there, power the device, and click Next. Once the blue message at the top of the page says Add new device now, follow the process as described in the user manual. To finish, choose a name for the new device, add the device to favorites (optional), edit the name, assign it to a room, and click I’m done adding devices
Go to the Settings from the side menu. From the Settings, tap on Learning Mode. To add this hub as a secondary controller, tap on Enable Learning mode Once you press Enable Learning mode, you will see the Learning mode process is started. It may take a few minutes
Once the inclusion is successfully finished you can start the Controller Replication process. Tap on the Start discovery button. The discovery process has been started and you can see how many devices are discovered in the Z-Wave network. Discovered devices will appear on the list of discovered devices. You can rename the discovered devices and assign them to a room. If you don’t want to rename or assign to a room, just tap the Finish button.
Factory reset Ezlo Plus
Find the "Reset" button on the controller near the Ethernet cable connector. Push and hold the RESET button for at least 5 sec (on Ezlo Plus LED starts blinking RED), After that your Ezlo controller will be reset to factory defaults. Reset to Factory Settings remove all the information about added devices and reset Z-Wave chip (new Home ID, new S0/S2 keys, remove all Z-Wave nodes), scenes created, House modes settings, etc. The process is irreversible
Go to the Devices screen and tap on the > button to see the device options and tap on the Z-Wave settings option On General settings, select Rediscover device and tap on it. On the rediscovery device screen tap on the Rediscover button. The rediscovery process will start
The Exclusion process can be started via UI.
From the list of devices, tap on the selected device and go to that device's settings. On the device settings screen press "Delete device". Select "Unpair" if your device is still connected to your network. "Unpair" will redirect you through the excluding wizard of the device. You need to have physical access to the device as well.
For the devices that have a button, it usually involves pressing that button a number of times.
Check the device manufacturer manual as well.
SmartStart installation
With Smart Start, you can add Z-Wave devices automatically by scanning their QR codes.From your Dashboard, go to Devices > tap on the + in the top right corner.Select the Z-Wave Smart Start entry. Tap on the Arrow next to the text.On the box of your device, you should find a QR code, usually labeled with a Smart Start title. When you select "Z-Wave Smart Start" in the iOS app, the camera of your phone will be turned on to scan the QR-code. Once a QR code has been scanned the adding process starts. The device is added to the system and you will see a Set Up Device screen. To continue, choose a name for the new device, edit the name, assign it to a room, and click Continue The device is added to the system and you will see a Set Up Device screen. To continue, choose a name for the new device, edit the name, assign it to a room, and click Continue Select the inclusion type - Smart Start. Tap on the Continue button. In the next step, you will see the confirmation screen that your device is ready. Just turn on your device and it will be added automatically. You can check the Smart Start device state in Settings Turn on your device. You will get a push notification New device is available. Tap on the notification and the VeraMobile app is opened to the list of Smart Start devices.
From your Dashboard navigate to Settings> SmartStart Devices screen with a SmartStart Provisioning List.
Tap on the Info button and see the device details on an additional screen. On this screen, you can change the device name, the encryption connection, and the inclusion type.
Please note that this is a user manual Ezlo Plus from eZLO is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Ezlo Plus and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.