Secure (EzloSecure-US) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Secure (EzloSecure-US)from eZLO. To view other Z-Wave products and manuals from eZLO follow that link.

1. Overview
2. Security
3. Features
4. Installation instructions

Overview

Security

As a Z-Wave Plus certified product, Secure supports Z-Wave S2 security. The following security modes are directly supported:

• S2 Access Control
• S2 Authenticated
• S2 Unauthenticated

Features

eZLO describes Secure as having the following features:

• Thermostat Modes
• FLiRS capable
• Supports Network Wide Inclusion
• Supports Z-Wave Explorer Frames
• Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: The full DSK can be found on the Ezlo Secure product packaging.
The first 5 DSK digits (PIN) is placed on the bottom of the Ezlo Secure product

The Classic Inclusion process can be started via UI.
From your Dashboard, go to Devices > tap on the + in the top right corner and select or
search the name or type of device that you wish to pair with Ezlo Secure.
To add a generic Z-Wave device, select the Generic Z-Wave device from the device
categories.
To add the device with your Ezlo Secure, if the device requires assembly read the
manual, follow the assembly instructions there, power the device, and click Next.
Once the blue message at the top of the page says Add new device now, follow the
process as described in the user manual.
To finish, choose a name for the new device, add the device to favorites (optional), edit
the name, assign it to a room, and click I’m done adding devices

The Exclusion process can be started via UI.
From the list of devices, tap on the selected device and go to that device's settings
On the device settings page press delete device
Select unpair if your device is still connected to your network, and delete if the device is
no longer connected.
Unpair will redirect you through the excluding wizard of the device. You need to
have physical access to the device as well

Go to the Settings from the side menu.
From the Settings, tap on Learning Mode.
To add this hub as a secondary controller, tap on Enable Learning
mode
Once you press Enable Learning mode, you will see the Learning mode
process is started. It may take a few minutes

Once the inclusion is successfully finished you can start the Controller
Replication process.
Tap on the Start discovery button.
The discovery process has been started and you can see how many
devices are discovered in the Z-Wave network.
Discovered devices will appear on the list of discovered devices. You
can rename the discovered devices and assign them to a room. If you
don’t want to rename or assign to a room, just tap the Finish button.

Navigate to Start Devices screen with a list of devices
Tap on the Info button and see the device details in an additional screen.
On this screen you can change the device name, the encryption connection,
and the inclusion type. To change the encryption connection, tap on the >
button.

Factory reset Secure

Find the "Reset" button on the controller near the Ethernet cable connector.
Push and hold the RESET button for at least 5 sec (on Ezlo Secure LED starts blinking RED), After that your Ezlo controller will be reset to factory defaults.
Reset to Factory Settings remove all the information about added devices
and reset ZWave chip (new Home ID, new S0/S2 keys, remove all Z-Wave
nodes), scenes created, House modes settings, etc. The process is
irreversible.

Go to the Devices screen and tap on the > button to see the device options and tap on
the Z-Wave settings option
On General settings, select Rediscover device and tap on it.
On the rediscovery device screen tap on the Rediscover button. The rediscovery
process will start

SmartStart installation

With Smart Start, you can add Z-Wave devices automatically by scanning their QR codes.
From your Dashboard, go to Devices > tap on the + in the top right corner.
Select the Z-Wave Smart Start entry. Tap on the Arrow next to the text.
On the box of your device, you should find a QR code, usually labeled with a Smart Start
title. When you select "Z-Wave Smart Start" in the iOS app, the camera of your phone
will be turned on to scan the QR-code. Once a QR code has been scanned the adding
process starts.
The device is added to the system and you will see a Set Up Device screen. To continue,
choose a name for the new device, edit the name, assign it to a room, and click
Continue
The device is added to the system and you will see a Set Up Device screen. To continue,
choose a name for the new device, edit the name, assign it to a room, and click
Continue
Select the inclusion type - Smart Start. Tap on the Continue button.
In the next step, you will see the confirmation screen that your device is ready.
Just turn on your device and it will be added automatically. You can check the Smart
Start device state in Settings
Turn on your device. You will get a push notification New device is available.
Tap on the notification and the VeraMobile app is opened to the list of Smart Start
devices.

Please note that this is a user manual Secure from eZLO is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Secure and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.