The following is an overview of the user manual for the Z-Wave product Zws12 (ZWS12 RU)from FAKRO. To view other Z-Wave products and manuals from FAKRO follow that link.
Overview
The chain has 2 output speed and reach 24cm.
The ZWS12 motor is equipped with encoder and two limit switches:
limit switch at maximum chain travel position,
overload limit in both directions (used mainly when closing the window).
This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers.
ZWS12 also can be controlled manually by button and closed by rain sensor and timer.
There are four association groups in actuator ZWS12:
Life Line – group for position reporting actuator after each a stoppage and alarm reporting
Basic Repeat – group used to transfer the received basic commands to the devices included in this group.
Multilevel Repeat – group used to transfer the received multilevel commands to the devices included in this group.
Basic Rain – group used to transfer the received commands from actuator & rain detector to the devices included in this group.
Z-Wave Plus Secure Enabled Product
This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products.
Technical Parameters:
Chain reach: 240 mm
Output power : 9 W
Rated current: 0.72 A
Standby current: 0.03 A
Chain pushing force: 250 N
Closing force: 200 N
Current limit: YES
Power voltage: 15V DC
Power cable: 2 x 0.75 mm2 (0,4 m)
Security
As a Z-Wave Plus certified product, Zws12 supports Z-Wave S2 security. The following security modes are directly supported:
Features
FAKRO describes Zws12 as having the following features:
- Window Covering Control Features
- Color
- Sensors
- Switch Type
- Supported Notification Types
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Autoinclusion - This feature allow you to add hard to reach devices to Z-Wave network. 3-times ON and OFF the power actuator (OFF-ON-OFFON-OFF-ON) causes the introduction of actuator to Autoinclusion mode.
Please note that the procedure has been started the time between on and off can not exceed 20s. Autoinclusion mode is activated for a maximum of 10 minutes. During this time, we can add an actuator to any Z-Wave controller running in the Include procedure.
Include - This function allow you to add actuator to the network Z-Wave.
Follow the procedure adding device to the network Z-Wave according to user manual supplied with the product. Then, press the programming button P on the actuator for 1 second.
Exclude - This function allow you to remove actuator from the network Z-Wave. Follow the procedure removing device from the network Z-Wave
according to user manual supplied with the product. Then, press the
programming button P on the actuator for 1 second. Function removes
information only about network Z-Wave.
Factory reset Zws12
Device Reset Locally – This function allows you to reset the Z-Wave
network without the use of Z-Wave controller. Press 5 times the
programming button P fast, the actuator was removed from the Z-Wave
network, restore the default parameters, name and locations.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Autoinclusion - This feature allow you to add hard to reach devices to Z-Wave network. 3-times ON and OFF the power actuator (OFF-ON-OFFON-OFF-ON) causes the introduction of actuator to Autoinclusion mode. Please note that the procedure has been started the time between on and off can not exceed 20s. Autoinclusion mode is activated for a maximum of 10 minutes. During this time, we can add an actuator to any Z-Wave controller running in the Include procedure.
Please note that this is a user manual Zws12 from FAKRO is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Zws12 and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.