Wall Plug US (FGWPB-111) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Wall Plug US (FGWPB-111)from FIBARO. To view other Z-Wave products and manuals from Fibaro follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


Wall Plug US
SKU Code
FIBARO Wall Plug is a remotely controlled plug-in switch with the ability to measure power and energy consumption. It uses a LED frame to visualize the current load and operating mode with color changing illumination. FIBARO Wall Plug makes it possible to control electrical devices in a convenient and maintenance-free way.
Main features of FIBARO Wall Plug:
- Compatible with any Z-Wave or Z-Wave+ Controller.
- Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 with PRNG-based encryption.
- Extremely easy installation - simply plug the device into the mains socket.
- Works as a Z-Wave signal repeater.
- Active power and energy consumption metering for plugged device.
- Current value of the load and operating mode are indicated by the multi-color LED frame.
Version #
HW: 1 FW: 4.01:04.01 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, Wall Plug US supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


Fibaro describes Wall Plug US as having the following features:

  • Supported Notification Types
  • Switch Load Capacity Current
  • Electric Load Type
  • Switch Load Capacity Volt-Ampere
  • Supported Meter Type
  • Sensors
  • Firmware updatable via a compatible Z-Wave gateway
  • Color
  • Loads Controlled
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

To remove the device from the Z-Wave network:
1. Plug the device into a socket nearby the main Z-Wave controller.
2. The LED frame will glow green signaling being added (removing is not necessary otherwise).
3. Set the main controller into remove mode.
4. Quickly, triple click the button located on the casing.
5. Wait for the removing process to end.
6. Successful removing will be confirmed by the Z-Wave controller’s message.

FIBARO Wall Plug is powered with mains voltage so it is always awake.

To add the device to the Z-Wave network:
1. Plug the device into a socket nearby the main Z-Wave controller.
2. The LED frame will glow red signaling not being added (reset or remove the device otherwise).
3. Set the main controller in (security/non-security) add mode.
4. Quickly, triple click the button located on the casing.
5. If you are adding in S2 authenticated mode, type in the device pin code (underlined part of the public key available on the device or in the manual).
6. Wait for the adding process to end.
7. Successful adding will be confirmed by the Z-Wave controller’s message.

Factory reset Wall Plug US

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted.
1. Make sure the device is powered.
2. Press and hold the button.
3. Wait for the LED frame to glow yellow (3rd menu position).
4. Release the button.
5. Click the button once to confirm selection.
6. After few seconds the device will restart with factory settings, which is signaled with the red frame color.

Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use the reset procedure only if the primary controller is missing or inoperable.

Please note that this is a user manual Wall Plug US from FIBARO is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Wall Plug US and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.