The following is an overview of the user manual for the Z-Wave product Walli Controller (FGWCEU-201)from Fibar Group S.A.. To view other Z-Wave products and manuals from Fibaro follow that link.
Overview
Main features:
• Can be used for controlling various types of Z-Wave devices, e.g. switches, dimmers, roller shutters.
• Is a part of FIBARO Walli line of smart devices.
• Pre-set configurations allow to easily adjust operation for specific type of controlled devices.
• May be installed on a smooth surface or on a mounting box.
• Can be powered using battery or VDC power supply.
• Is equipped with a built-in temperature sensor.
• Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption.
• Works as a Z-Wave signal repeater when VDC powered.
Security
As a Z-Wave Plus certified product, Walli Controller supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Fibaro describes Walli Controller as having the following features:
- Battery powered using ER14250 batteries
- Color
- Firmware updatable via a compatible Z-Wave gateway
- Z-Wave Scene Type
- Battery Quantity
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Factory reset Walli Controller
1. Quickly, three times click, then press and hold one of the buttons
for 21 seconds.
2. Release the button when the device glows yellow.
3. Quickly click the button to confirm.
4. After a few seconds the device will be restarted, which is signalled
with red LED colour.
The device will select the powering mode during adding
to the Z-Wave network, prioritizing external power supply
if connected. To change the mode after adding, you must
change the installation accordingly, then remove and add
the device again.
The capabilities of the device are changed at the level of adding the device to the network. So rediscover is not needed.
SmartStart location
SmartStart QR code's location as follows: If you are adding in Security S2 Authenticated, input the underlined
part of the DSK (label on the bottom of the box).
1. Set the main controller into remove mode (see the controller’s
manual).
2. Quickly, three times click, then press and hold one of the buttons
for 12 seconds.
3. Release the button when the device glows green.
4. Quickly click the button to confirm.
5. LED will start blinking yellow, wait for the removing process to
end.
6. Successful removing will be confirmed by the Z-Wave controller’s
message and red LED colour.
1. Quickly, three times click, then press and hold one of the buttons.
2. After 3 seconds LED ring signals adding status:
• Blinking green – entering the menu (added as non-secure, S0,
S2 non-authenticated)
• Blinking magenta – entering the menu (added as Security S2
Authenticated)
• Blinking red – entering the menu (not added to a Z-Wave
network)
3. The LED ring will turn off for 3 seconds, then start signalling menu
positions.
4. Release the button when device signals desired position with
colour:
• WHITE – wake up the device
5. Quickly click the button to confirm.
1. Set the main controller in (Security/non-Security Mode) add mode
(see the controller’s manual).
2. Quickly, three times click one of the buttons.
3. If you are adding in Security S2 Authenticated, input the underlined
part of the DSK (label on the bottom of the box).
4. LED will start blinking yellow, wait for the adding process to end.
5. Adding result will be confirmed by the Z-Wave controller’s message
and the LED frame:
• Green – successful (non-secure, S0, S2 non-authenticated),
• Magenta – successful (Security S2 Authenticated),
• Red – not successful.
Please note that this is a user manual Walli Controller from Fibar Group S.A. is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Walli Controller and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.