Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Forest Shuttle LZ ANZ (FS2Z5232000007) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Forest Shuttle LZ ANZ (FS2Z5232000007)from Forest Drapery Hardware. To view other Z-Wave products and manuals from Forest Drapery Hardware follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Forest Shuttle LZ ANZ
SKU Code
FS2Z5232000007
Description
Forest Shuttle L Z-wave, Shuttle S Z-wave (US) and Forest motorized curtain track systems (FMS) make an unbeatable combination when it comes to noiseless operated motorized curtains. The smooth and silent running curtain track system can, in addition to remote operation, also be operated by hand. Thanks to Forest’s special Touch Impulse Technology, a gentle pull on the curtain is enough to activate the motor. The Forest Shuttle L Z-wave, Shuttle S Z-Wave (US) makes sure that your curtains will always hang beautifully smooth and supple. Opened as well as closed!
• Touch Impulse Technology, gently pulling the curtain will activate the motor.
• Integrated Emergency Control ensures manual operation of the curtain in case of power failure.
• Modular motor, different modules can be attached for various control options: Radio Frequency, Switch, Infrared, Domotics, Building/Hotel Automation, Serial Communication, Z-Wave, etc.
• Forest Shuttle L Z-Wave and Shuttle S Z-wave (US) will have an internal Z-Wave receiver and BUS connection.
• Silent motor, speeds: 14 and 17 cm/sec., with slow start and slow stop.
• Full automatic setting of the limits.
• Stack-back position programmable to every desired setting.
• Forest Shuttle L Z-Wave and Shuttle S Z-wave (US) have an integrated power supply.
• Motor pulley connects motor and FMS track. Also available in upside down version to conceal the motor into the ceiling.
• Available track lenghts: 5.80 meters and 7.00 meters. FMS track and components available in white, grey and black.
Version #
HW: 1 FW: 1.00 was the version certified
Certification #
ZC10-19016362
Certified
2019-01-29T22:13:45.601388
Z-Wave Version
6.51.10

Security

As a Z-Wave Plus certified product, Forest Shuttle LZ ANZ supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    Forest Drapery Hardware describes Forest Shuttle LZ ANZ as having the following features:

    • Switch Load Capacity Watts
    • Window Covering Control Features
    • Firmware updatable via a compatible Z-Wave gateway
    • Switch Load Capacity Current
    • Switch Load Capacity Volt-Ampere
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    Factory reset Forest Shuttle LZ ANZ

    Press configuration button 25x times. LED 1 is ON. Press and hold once more for 4 seconds to confirm.
    Please use this procedure only when your network primary controller is missing or otherwise inoperable.

    Press configuration button 3 times. LED3 is ON.
    Press and hold once more for 4 seconds.

    Press configuration button 3 times. LED3 is ON.
    Press and hold once more for 4 seconds.

    Please note that this is a user manual Forest Shuttle LZ ANZ from Forest Drapery Hardware is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Forest Shuttle LZ ANZ and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.