Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Direct-Wire Outdoor Smart Switch (40 Amp) (14285/ZW4007) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Direct-Wire Outdoor Smart Switch (40 Amp) (14285/ZW4007)from GE. To view other Z-Wave products and manuals from GE follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Direct-Wire Outdoor Smart Switch (40 Amp)
SKU Code
14285/ZW4007
Description
Transform any home into a smart home with the GE 40 Amp Z-Wave Direct-Wire Indoor/Outdoor Smart Switch. When added to a Z-Wave network, the heavy duty switch enables wireless control of on/off functions for large load, hard-wired applications such as waters heaters, landscape lighting, spas, pool pumps and heaters. The Smart Switch can be used indoors or outdoors and features an easy access wire connection block, front mounted LED lights indicating power and on/off status, and an override switch to turn connected devices on or off manually. The Smart Switch is housed in a lockable, tamper-resistant case to ensure settings and wiring are secure. The rugged, weather-resistant design will keep out dirt and debris while being suitable for use in extreme weather conditions. The GE Z-Wave Direct-Wire Outdoor Smart Switch is also equipped with state-of-the-art energy monitoring capability, allowing you to monitor watts and kilowatt hours, helping you keep your energy costs to a minimum. Take control of your home lighting and large load devices with GE Z-Wave Smart Lighting Controls!
Version #
HW: 255 FW: 5.53 was the version certified
Certification #
ZC10-18056123
Certified
2018-05-25T18:51:19.456276
Z-Wave Version
6.81.01

Security

As a Z-Wave Plus certified product, Direct-Wire Outdoor Smart Switch (40 Amp) supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated

Features

GE describes Direct-Wire Outdoor Smart Switch (40 Amp) as having the following features:

  • Firmware updatable via a compatible Z-Wave gateway
  • Switch Load Capacity Current
  • Loads Controlled
  • Outdoor Use
  • Supported Meter Type
  • Z-Wave Scene Type
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

Factory reset Direct-Wire Outdoor Smart Switch (40 Amp)

1. Place the device into ON mode (upper position of Operating Mode Switch)
2. Press and hold the programming button.
3. While holding programming button, place device into OFF mode (middle position of Operating Mode Switch).
4. While holding programming button, place device back into ON mode (upper position of Operating Mode Switch).
5. After three (3) seconds, release programming button. Green LED will flash 3 times when completed successfully.

Note: This should only be used in the event your network’s primary controller is missing or otherwise inoperable.

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device press and release the programming button to remove it from the network.

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press and release the programming button to add it to the network. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product.
3. Once your controller has confirmed that the device has been added, refresh the Z-Wave network to optimize performance.

Please note that this is a user manual Direct-Wire Outdoor Smart Switch (40 Amp) from GE is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Direct-Wire Outdoor Smart Switch (40 Amp) and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.