The following is an overview of the user manual for the Z-Wave product Z-Wave Smart Motor Actuator (IoTx-z-actmotor001)from Ger-IoTx. To view other Z-Wave products and manuals from Ger-IoTx follow that link.
Overview
The actuator can control window covering devices like roller shutters, awnings, roller blinds and motorized curtains.
Security
As a Z-Wave Plus certified product, Z-Wave Smart Motor Actuator supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Unauthenticated
Features
Ger-IoTx describes Z-Wave Smart Motor Actuator as having the following features:
- Window Covering Control Features
- Supported Notification Types
- Supported Meter Type
- Firmware updatable via a compatible Z-Wave gateway
- Switch Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: page 1：The encryption modes that the in-wall shutter module supports are S0, S2 authenticated.
page 7: SUPPORTED COMMAND CLASS
Make sure connecting module to power supply and module has not joined Z-Wave network (if module joined any other Z-Wave network, please refer to the clauses “Exclude device from a Z-Wave network”).
First, set primary controller/gateway into inclusion mode. And press 'Button L' 3 times, LED starts to flash slowly for 10 seconds, during the flash, don’t press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success. If module does not find a Z-Wave network within 10 seconds after join network function trigger, please try again. After joined Z-Wave network, please wait for a while until the app showing device is included. Then you can start enjoying with our module.
Method 1: Factory Reset.
Method 2: First, set primary controller/gateway into exclusion mode. And press 'Button L' 3 times, LED started to flash slowly for 10 seconds, during the flash, don’t press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success.
Make sure connecting module to power supply and module has not joined Z-Wave network (if module joined any other Z-Wave network, please refer to the clauses “Exclude device from a Z-Wave network”).
First, set primary controller/gateway into inclusion mode. And press 'Button L' 3 times, LED starts to flash slowly for 10 seconds, during the flash, don’t press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success. If module does not find a Z-Wave network within 10 seconds after join network function trigger, please try again. After joined Z-Wave network, please wait for a while until the app showing device is included. Then you can start enjoying with our module.
Method 1: Factory Reset.
Method 2: First, set primary controller/gateway into exclusion mode. And press 'Button L' 3 times, LED started to flash slowly for 10 seconds, during the flash, don’t press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success.
Module is learning motor running position automatically each time when it’s pot on power supply.Tap Button R two times, learning function start, motor is running automatically to the up/down limit. During learning, LED light is flash slowly, until LED blink 2 seconds means success. During learning, press Button R to quit learning.
Factory reset Z-Wave Smart Motor Actuator
Please use this procedure only when the network primary controller is missing or otherwise inoperable. Hold Button L for 10 seconds, LED will flash slowly until flash fast for 2 seconds means success. After reset, module is exclude of Z-Wave network, please include again and learn motor again.
Module is learning motor running position automatically each time when it’s pot on power supply.Tap Button R two times, learning function start, motor is running automatically to the up/down limit. During learning, LED light is flash slowly, until LED blink 2 seconds means success. During learning, press Button R to quit learning.
Please note that this is a user manual Z-Wave Smart Motor Actuator from Ger-IoTx is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Smart Motor Actuator and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.