The following is an overview of the user manual for the Z-Wave product Z-Push Wall Controller (Z-Push Wall Controller)from Heatit controls. To view other Z-Wave products and manuals from Heatit follow that link.
Overview
The Heatit Z-Push Wall Controller is supplied with all three sets of rockers in the box. The Wall Controller is coin cell battery powered.
The product is intended primarily for residential applications.
The Heatit Z-Wall Wall Controller has a fine, matt finish.
The switch fits into System 55 frames.
Security
As a Z-Wave Plus certified product, Z-Push Wall Controller supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Heatit describes Z-Push Wall Controller as having the following features:
- Outdoor Use
- Battery powered using CR2450 batteries
- IP (Ingress Protection) Rated
- Battery Quantity
- Z-Wave Scene Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: The QR-Code is needed when including a device using S2 security or SmartStart. The DSK can be found in the QR-Code and is located;
1. On the product.
2. On the Quick Guide manual.
3. On the product box.
The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode.
There are two ways to add the device to a Z-Wave network.
Method 1: Standard (Manual)
Initiate the learning mode in the controller.
Press any UP button 6 times within 3 seconds.
When the add mode has started, the LED corresponding to the button you pressed will blink green. The device will indicate ”Success” by emitting a green light for 3 seconds.
Method 2: SmartStart (Automatic)
SmartStart-enabled products may be added to a Z-Wave network by scanning the Z-Wave QR-Code on the product if your primary controller supports SmartStart inclusion. No further action is required and the SmartStart product will be added automatically after being powered on within range of the primary controller.
The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode.
When the device is removed from the network, it will NOT revert to factory settings.
To manually wake up the device, please press any down button 6 times. The device will light up in green until wake up is no longer active. The default wake up interval in seconds: 604 800 (1 week).
Factory reset Z-Push Wall Controller
To factory reset the device, remove the battery from the device. Press and hold any button on the device and repower the device. The LEDs will start blinking 3 times before lighting up in green. When the green LED is on, you can release the button. The device will issue a Device Reset Locally Notification Command to notify that the device will be reset to default. When preforming a factory reset the device will lose its Node ID from the gateway and reset its Home ID.
Paragraph 5 Choosing the correct front/assembly
5.1 Single rocker configuation When the device is in single rocker configuration, it uses associations group 3. Change Parameter 3 to 1 when using a single rocker.
5.2 Dual rocker configuration
When the device is in dual rocker configuration, it uses associations group 2 for the first button and 4 for the second button.
Change Parameter 3 to 2 when using dual rockers.
5.3 Triple rocker configuration
When the device is in triple rocker configuration, it uses associations group 2 for the first button, 3 for the
second and 4 for the third button.
Change Parameter 3 to 3 when using dual rockers.
Please note that this is a user manual Z-Push Wall Controller from Heatit controls is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Push Wall Controller and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.