The following is an overview of the user manual for the Z-Wave product Z-Wave (TF021)from Heatit controls. To view other Z-Wave products and manuals from Heatit follow that link.
Overview
can be connected to Home Automation systems like Fibaro, Sensio, Vera, Zipato and others.
The display will show the actual room temperature. By pressing the buttons, the display will show the set value.
Heatit Z-Wave is equipped with a single-pole switch.
The thermostat can handle loads up to 16A/3600Wat 230V. If the load is greater than this, the thermostat needs to be connected to a contactor. It can be used with two external temperature sensors.
FUNCTIONS
• Room sensor
• Floor sensor
• Temperature limiter
• Power regulator
• Z-Wave chip 500 series
• Week program/setback temperature via gateway
• Setback mode
• 7-segment LCD-screen
• Can be used in connection with diff erent NTC-sensors
• Lock mode/child lock
• Backlight
• Calibration
• 8 scenarios
CONNECTION CLAMPS
Use 1,5 mm² or 2,5 mm² cables according to power need.
TECHNICAL DATA
Rated voltage: 230V 50/60Hz
Max. load: 3600W
Max. current: 16A
Power consumption: 1,5W
Protection class: IP21
Min/Max installation temp: -20°C to 40°C
Min/Max operating temp: 5°C to 40°C
Temperature intervals: Floor sensor 5°C to 40°C
Room sensor 5°C to 40°C
Hysteresis: 0,5°C
Sensor values: 0°C 29,1 kOhm
10°C 18,6 kOhm
15°C 15,1 kOhm
20°C 12,2 kOhm
25°C 10,0 kOhm
Switch: Single-pole
Security
As a Z-Wave Plus certified product, Z-Wave supports Z-Wave S2 security. The following security modes are directly supported:
Features
Heatit describes Z-Wave as having the following features:
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
INCLUSION/EXCLUSION
To include the thermostat to your home automation gateway, press Center (confirm) for 10 seconds.
The display will show OFF. Press Right (down) 4 times till you see Con in the display.
Now start add device in your home automation software. Start inclusion mode by pressing Center (confirm) for approximately
2 seconds. The inclusion/exclusion icon will appear in the display. Confirmation will show Inc/EcL in the display. If inclusion
fails, Err (error) will appear.
Leave programming mode by choosing ESC in menu. Your thermostat is ready for use with default settings.
INCLUSION/EXCLUSION
To include the thermostat to your home automation gateway, press Center (confirm) for 10 seconds.
The display will show OFF. Press Right (down) 4 times till you see Con in the display.
Now start add device in your home automation software. Start inclusion mode by pressing Center (confirm) for approximately
2 seconds. The inclusion/exclusion icon will appear in the display. Confirmation will show Inc/EcL in the display. If inclusion
fails, Err (error) will appear.
Leave programming mode by choosing ESC in menu. Your thermostat is ready for use with default settings.
Factory reset Z-Wave
FACTORY RESET - RES
By pressing buttons Left and Center (up and confirm) for 20 seconds, the thermostat will perform a complete factory reset.
NB! Please use this procedure only when the primary controller is missing or otherwise inoperable.
Please note that this is a user manual Z-Wave from Heatit controls is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.