The following is an overview of the user manual for the Z-Wave product Heating Thermostat (HE-HT01)from HELTUN. To view other Z-Wave products and manuals from Heltun follow that link.
Overview
You can monitor and control the HE-HT01 from anywhere in the world using a Z-Wave hub and your smartphone.* And because it uses the Z-Wave 700 Platform, SmartStart, and S2 Security, the HE-HT01 can be placed up to 100 meters away from the hub and is a snap to install. Best of all, real-time and cumulative energy consumption meters help you save money on energy costs while staying comfortable all year long.
The HELTUN HE-HT01 is part of an entire line of smart, connected products designed to provide the best technology has to offer without compromising stylish living.
(*hub and smartphone not included)
Security
As a Z-Wave Plus certified product, Heating Thermostat supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Heltun describes Heating Thermostat as having the following features:
- Neutral Wire Required
- Switch Load Capacity Current
- Switch Load Capacity Watts
- Switch Type
- Thermostat HVAC Systems Supported
- Thermostat Modes
- Thermostat Power Source
- Firmware updatable via a compatible Z-Wave gateway
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: The device DSK and QR code are printed on the HE-HT01 back panel plus on the manual included in the HE- HT01 packaging.
Factory reset Heating Thermostat
By pressing and holding the “MODE” key for ten seconds, the HE-HT01 will enter Factory Reset Mode, displaying “REs” in the left bottom corner, “y” in top left corner and “n” in top right corner. Press the Plus (+) button to revert to factory settings, or the Heating Element button to cancel. The factory reset will change all the Parameters to their original factory default values and will also Exclude the device from any Z-Wave network.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
To remove HE-HT01 from a Z-Wave network (exclusion), do the following:
1. Enter “SETTINGS” Mode by pressing and holding the Gear button for three seconds.
2. Scroll menu to “Parameter 31 – nEt” using the Heating Element button to scroll up, and the “MODE” button to scroll down.
3. The current state of the network will display in the Parameter Value position (upper right). It should display “InC”. Note: If “EcL” is displayed, the HE-HT01 is already Excluded.
4. Start the Exclusion Mode from the gateway/controller.
5. Press the Minus “–” button in the HE-HT01 Parameter 31 to start the Exclusion process
6. Note that lines will be moving in the Parameter value position (upper right).
7. The Antenna icon should appear in the bottom right corner and “EcL” in the value position if the Exclusion was successful.
8. If the Antenna with signal strength bars icon or “InC” in value position are displayed, repeat the Exclusion process.
To add HE-HT01 into a Z-Wave network (inclusion), do the following:
1. Enter “SETTINGS” Mode by pressing and holding the Gear button for three seconds.
2. Scroll menu to “Parameter 31 – nEt” using the Heating Element button to scroll up, and the “MODE” button to scroll down.
3. The current state of the network will display in the Parameter Value position (upper right). It should display “EcL”. Note: If “Inc” is displayed, the HE-HT01 must first be Excluded from an existing Z-Wave network (see “Exclusion” below).
4. Start the Inclusion Mode from the gateway/controller.
5. On the HE-HT01 in the Parameter 31 press the Plus “+” key to start the Inclusion process.
6. Note that lines will be moving in the Parameter value position (upper right).
7. The Antenna with signal strength bars icon should appear at the bottom right corner if Inclusion was successful.
8. If only the Antenna icon is displayed or “Err” is on Value position, the HE-HT01 Inclusion was not successful (try repeating steps 4-7).
Please note that this is a user manual Heating Thermostat from HELTUN is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Heating Thermostat and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.