The following is an overview of the user manual for the Z-Wave product High Load Switch (HE-HLS01)from HELTUN. To view other Z-Wave products and manuals from Heltun follow that link.
Overview
It can also provide Internet-connected thermostat functions where a local display and controls are not needed. HELTUN HE-HLS01 fits easily behind outlets or switches in standard electrical junction boxes.
Features:
• 16A maximum load
• 10 scenarios for output control
• 6 thermostat operating modes
• 4 association groups
• External NTC sensor
• Real time energy consumption meter
• Onboard Real Time Clock (RTC)
• 8 safety functions & notifications
• Works both with VAC 85-265 and VDC 24-48
• Incorporates HELTUN Advanced Zero-Cross Technology
The HELTUN HE-HLS01 is part of an entire line of smart, connected products designed to provide the best technology has to offer without compromising stylish living.
Learn more about HELTUN products at www.heltun.com
Security
As a Z-Wave Plus certified product, High Load Switch supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Heltun describes High Load Switch as having the following features:
- Thermostat Power Source
- Switch Load Capacity Watts
- Switch Load Capacity Current
- Neutral Wire Required
- Firmware updatable via a compatible Z-Wave gateway
- Switch Type
- Thermostat HVAC Systems Supported
- Thermostat Modes
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: The device security code (DSK) and SmartStart QR code are printed on the rear and front of the HE-HLS01 plus on the additional Security Card included in the packaging
Factory reset High Load Switch
To reset the HE-HLS01 to factory defaults, press and hold the service button for six seconds.
If successful, the LED indicator will blink white for two seconds then the device will reboot.
The factory reset will change all the Parameters to their original factory default values and will also Exclude the device from any Z-Wave network.
Note: Please use this procedure only when the network primary controller is missing or otherwise inoperable.
To add the HE-HLS01 to an existing Z-Wave network (i.e. “inclusion”), do the following:
1. Ensure the HE-HLS01 is Powered On and the LED indicator blinks red slowly (i.e. it is excluded).
2. Start the Inclusion Mode from the gateway/controller.
3. To start the inclusion process on the HE-HLS01:
a) if you want to use the device as a “Binary Switch”, double-press the service button on the device (with no more than a one-second interval between presses).
b) if you want to use the device as a “Thermostat”, press four times the service button on the device (with no more than a one-second interval between presses).
4. The LED indicator will blink green quickly.
5. If the inclusion has been successful, the LED indicator will turn green for three seconds then continue slowly blinking green continuously while the HE-HLS01 is Powered On.
6. If the inclusion was not successful, the LED indicator will turn red for three seconds then continue slowly blinking red continuously while the HE-HLS01 is Powered On. In that case repeat the inclusion process (2-5) above.
The device type is "Binary Switch" by default.
Depending on the inclusion method it is possible also to use that as "Thermostat".
To start the inclusion process on the HE-HLS01:
a) if you want to use the device as a “Binary Switch”, double-press the service button on the device (with no more than a one-second interval between presses).
b) if you want to use the device as a “Thermostat”, press four times the service button on the device (with no more than a one-second interval between presses).
The altered capabilities are described in the corresponding sections in user manual:
Functions & Features
Device type “Binary Switch”
Device type “Thermostat”
The functions and features of HE-HLS01 could be different depending on how the device is included in Z-Wave network.
Depending on the number of button presses (two or four) during the inclusion process HE-HLS01 could function as either “Binary Switch“ or “Thermostat“.
In case if the device is already included in Z-Wave network and there is a need to change the device type, it should be removed from network and re-included with the corresponding type.
To remove the HE-HLS01 from a Z-Wave network (i.e. “Exclusion”), do the following:
1. Ensure the HE-HLS01 is Powered On and the LED indicator blinks green slowly (i.e. it is included in a Z-Wave network). 1. Start the Exclusion Mode from the gateway/controller.
2. To start the exclusion process on the HE-HLS01, double-press the service button on the device (with no more than a one-second interval between presses).
3. The LED indicator will blink red quickly.
4. If the exclusion has been successful, LED indicator will turn red for three seconds then continue slowly blinking red continuously while the HE-HLS01 is Powered On.
5. If the exclusion was not successful, the LED indicator will turn green for three seconds then continue slowly blinking green continuously while the HE-HLS01 is Powered On. In that case repeat the exclusion process (2-5) above.
Note: If the HE-HLS01 has previously been part of a Z-Wave network and not Excluded since, Inclusion is not possible without first performing an Exclusion or Factory Reset procedure.
Please note that this is a user manual High Load Switch from HELTUN is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have High Load Switch and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.