The following is an overview of the user manual for the Z-Wave product Z-Wave 700 Series Cube (HOMEE-005)from homee. To view other Z-Wave products and manuals from homee follow that link.
Overview
You could use Z-Wave™ Cube to control your blinds and roller shutters by making them smart with the Fibaro Roller Shutter2 insert switch. You can define times when heating should be tuned to any chosen comfort temperature, saving you money on heating - this is no problem with the Danfoss LC-13 radiator thermostat. Via our homeegrams, radiator thermostats can automatically be switched off once a window is opened, helping you to prevent energy waste. If security is your concern, you can add devices such as smoke detectors to your home, which alert you via push notification of fire or smoke, while also opening the blinds and turning on lights in order to create escape routes.
Once you leave your apartment, you can enable homeegrams alerting you if one of your door, window or motion sensors detect an unexpected event during your absence. Additionally, you could fire off an alarm siren like the Aeotec Siren.
Security
As a Z-Wave Plus certified product, Z-Wave 700 Series Cube supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Access Control
- S2 Authenticated
- S2 Unauthenticated
Features
homee describes Z-Wave 700 Series Cube as having the following features:
- Gateway Has Preferred Partners
- Firmware updatable via a compatible Z-Wave gateway
- Communications Protocol
- Communications Connections
- Supported Notification Types
- Sensors
- Supported Meter Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
If the ZWave cube is reset to factory defaults, all connected Z Wave devices will be removed, and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to remove and add all of the nodes in the network.
If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.
Factory reset Z-Wave 700 Series Cube
If the Z Wave cub e is reset to factory defaults, all connected Z Wave devices will be removed, and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessar y after the reset to remove and add all of the nodes in the network.
If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller
Add Z-Wave Device (General)
Remove Z-Wave Device
SmartStart location
SmartStart QR code's location as follows: NOTE: The only way to see the DSK is via our app. The connection between our app and our
gateway is a secure websocket connection. The DSK is not pyhsically printed on the casing or packaging.
SmartStart installation
Add Z-Wave Device (SmartStart)
If the ZWave cube is reset to factory defaults, all connected Z Wave devices will be removed, and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to remove and add all of the nodes in the network.
If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.
Add Z-Wave Device (SmartStart)
Node Rediscovery
Please note that this is a user manual Z-Wave 700 Series Cube from homee is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave 700 Series Cube and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.