The following is an overview of the user manual for the Z-Wave product Smart In Wall Dimmer (HS-WX300)from HomeSeer. To view other Z-Wave products and manuals from HomeSeer follow that link.
Overview
Security
As a Z-Wave Plus certified product, Smart In Wall Dimmer supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
Features
HomeSeer describes Smart In Wall Dimmer as having the following features:
- Z-Wave Scene Type
- Color
- Firmware updatable via a compatible Z-Wave gateway
- Switch Load Capacity Watts
- Neutral Wire Required
- Outdoor Use
- Electric Load Type
- Switch Load Capacity Volt-Ampere
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: *QR Code is located on the HS-WX300 metal yoke under the switch paddle.
Factory reset Smart In Wall Dimmer
To be used only in the event that the network primary controller is lost or otherwise inoperable.
1. In rapid succession, tap the top paddle 3 times, then tap the bottom paddle 3 times. If all LEDs flash white 5 times, factory reset was successful. If not, repeat this procedure.
Note: As this must be done very quickly, we recommend using 2 fingers for this operation; one on each paddle!
Note: The switch will default to 3-wire mode and dimmer mode after factory reset.
Changing Wire Mode
HS-WX300 may be installed with a neutral wire (3-wire mode) or without a neutral wire (2-wire mode). Selecting the correct wire mode will yield the best results, especially if the switch is configured as a dimmer. By default, 3-wire mode is enabled. To change the wire mode (at the switch):
1. Turn the power off
2. In rapid succession, tap the top paddle 2 times, then press & hold the top paddle for 3 seconds (tap-tap-press & hold)
3. Observe the behavior of the LEDs
- If the bottom 3 LEDs flash white 3 times, HS-WX300 is configured for 3-wire mode
- If the bottom 2 LEDs flash white 2 times, HS-WX300 is configured for 2-wire mode
Note: Wire mode may also be changed by the hub using Z-Wave parameter 32. See the Z-Wave Parameters section at the end of this user guide.
Note: The switch will default to 3-wire mode and dimmer mode after factory reset.
Follow this 2-step procedure to add (or remove) your new HomeSeer switch to (or from) your Z-Wave network:
1. Put your Z-Wave controller into inclusion (or exclusion) mode. Consult your controller’s manual if you’re unsure how to do this.
2. In rapid succession, tap the bottom paddle 2 times, then press & hold the bottom paddle for 3 seconds (tap-tap-press & hold). This will initiate the inclusion (or exclusion) process. Note: The switch will default to dimmer mode after Z-Wave exclusion
Follow this 2-step procedure to add (or remove) your new HomeSeer switch to (or from) your Z-Wave network:
1. Put your Z-Wave controller into inclusion (or exclusion) mode. Consult your controller’s manual if you’re unsure how to do this.
2. In rapid succession, tap the bottom paddle 2 times, then press & hold the bottom paddle for 3 seconds (tap-tap-press & hold). This will initiate the inclusion (or exclusion) process. Note: The switch will default to dimmer mode after Z-Wave exclusion
Changing Switch Mode
(Must be done BEFORE Z-Wave inclusion)
HS-WX300 may be configured to operate as an ON-OFF switch or as a DIMMER. By default, it will operate as a dimmer. To change the switch mode, follow these steps:
1. Press & hold the small button located on the metal yoke next to the column of LEDs, OR if the trim plate is already installed, in rapid succession, tap the top paddle 3 times, then press & hold the top paddle for 3 seconds (tap-tap-tap-press & hold)
2. Observe the behavior of the LEDs
- If all LEDs blink green 3 times, HS-WX300 is configured to function as a dimmer
- If the bottom LED blinks blue 3 times, HS-WX300 is configured to function as an on-off switch
Please note that this is a user manual Smart In Wall Dimmer from HomeSeer is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Smart In Wall Dimmer and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.