Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

In-Wall Smart Dimmer (39351/ZW3010) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product In-Wall Smart Dimmer (39351/ZW3010)from Honeywell. To view other Z-Wave products and manuals from Honeywell follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
In-Wall Smart Dimmer
SKU Code
39351/ZW3010
Description
In-Wall Smart Dimmer with QuickFit and SimpleWire enhancements. Revolutionary QuickFit design features a housing depth that is up to 20 percent smaller than the previous Z-Wave models. This reduced size coupled with the elimination of heat taps provides a better fit in older style boxes and multi-gang configurations. SimpleWire technology allows line and load to automatically be configured with auto-sensing line-load terminals. All of this is coupled with Z-Wave S2 and Smart Start allows for effortless installation while being safer than ever!
Version #
HW: 255 FW: 5.53 was the version certified
Certification #
ZC10-19086695
Certified
2019-08-01T23:19:57.065818
Z-Wave Version
6.81.03

Security

As a Z-Wave Plus certified product, In-Wall Smart Dimmer supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated

Features

Honeywell describes In-Wall Smart Dimmer as having the following features:

  • Firmware updatable via a compatible Z-Wave gateway
  • Neutral Wire Required
  • Z-Wave Scene Type
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press and release the top or bottom of the wireless smart dimmer (rocker) to add it in the network.
If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product.

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press and release the top or bottom of the wireless smart dimmer (rocker) to remove it from the network.

Factory reset In-Wall Smart Dimmer

Quickly press ON (top) button 3 times, then, immediately press the OFF (bottom) button 3 times. The LED will flash 5 times when completed successfully.
Note: This should only be used in the event your network’s primary controller is missing or otherwise inoperable.


Button Press Functions

Cycle LED= Press 3 up then 1 down to cycle through LED status

Switch Mode = Press 5 up then 5 down if done successfully the LED will blink 5 times

Min Threshold = Press 4 down then 1 up, if done successfully the device will turn to 1% and the LED will start to blink signaling the device is in setup mode. Press and hold up or down to adjust the device to the desired minimum threshold.
Max Threshold = Press 4 up then 1 down, if done successfully the device will turn to 99% and the LED will start to blink signaling the device is in setup mode. Press and hold down or up to adjust the device to the desired maximum threshold.

Please note that this is a user manual In-Wall Smart Dimmer from Honeywell is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have In-Wall Smart Dimmer and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.