Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Der Aufpasser (3000117) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Der Aufpasser (3000117)from iamsmart. To view other Z-Wave products and manuals from iamsmart follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Der Aufpasser
SKU Code
3000117
Description
The iamsmart Window & Door Sensor is an ultra-thin magnetic contact sensor designed to monitor windows and doors for your safety and efficiency. It’s so thin that it can be mounted invisibly in a tiny gap between the frame and the door or window. It is as easy to mount as a sticker using the iamsmart Window & Door Sensor’s adhesive tape. The iamsmart Window & Door Sensor is a Z-Wave plus compliant and can be used with any existing Z-Wave smart home system. Combined with the iamsmart Smartbox and smart Radiator Thermostat, the Window & Door Sensor is also able to make your heating more efficient by detecting open windows and adjusting the temperature accordingly to not waste energy. To make your home more secure the iamsmart Smartbox and the Window & Door Sensor are the perfect team: the internal, very loud siren of the Smartbox scares robbers and is triggered by the iamsmart Window & Door Sensor if a window or door is opened while you’re away. Besides its main features – security and efficient heating in combination with the smart Radiator Thermostat, the iamsmart Window & Door Sensor has an impressive battery life of up to 10 years.
Version #
HW: 2 FW: 0.08:00.09 was the version certified
Certification #
ZC10-18026002
Certified
2018-02-12T19:00:56.08371
Z-Wave Version
6.51.06

Security

As a Z-Wave Plus certified product, Der Aufpasser supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    iamsmart describes Der Aufpasser as having the following features:

    • Sensors
    • Battery powered using Built in 3.0V LiMnO2 batteries
    • Color
    • Outdoor Use
    • Battery Quantity
    • Supported Notification Types
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    The iamsmart Window & Sensor is delivered in ""auto-add"" mode.
    Follow the process below to add the iamsmart Window & Sensor in a Z-Wave network.

    1. Start the add mode on the Z-Wave controller.
    See the controller’s manual.

    2. Remove both magnets from the iamsmart Window & Door Sensor. The iamsmart Window & Door Sensor blinks twice to confirm the command and successful addition.

    3. A long LED blink indicates that the add process was successful

    4. The Z-Wave controller application should now allow you to monitor your iamsmart Window & Door Sensor status.

    5. Move the squared magnet as shown in the picture . Check that the Z-Wave system indicates the status correctly.

    6. If the Z-Wave system does not respond, it may be needed to change the iamsmart Window & Door Sensor’s notification type.

    Manual add:
    1. Set the controller to add mode (See your controller’s manual).

    2. Place the round magnet at the rounded edge of the iamsmart Window & Door Sensor.
    When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds.

    3. A long LED blink indicates that the add process was successful.

    1. Set the controller in remove mode (See your controller’s manual).

    2. Place the round magnet at the rounded edge of the iamsmart Window & Door Sensor.
    When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds.

    3. A long LED blink indicates that the remove process was successful.

    Failure message: 5 LED blinks

    Wake up the iamsmart Window & Door Sensor manually for Z-Wave communication:

    1. Place the round magnet at the rounded edge of the iamsmart Window & Door Sensor.

    2. When the LED blinks, move the magnet away.

    3. Repeat 3 times in total within 10 seconds.

    Factory reset Der Aufpasser

    In order to reset the iamsmart Window & Door Sensor (needed when the controller is lost or inoperable):

    1. Place the round magnet at the rounded edge of the iamsmart Window & Door Sensor.

    2. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds.

    3. On the 3rd repetition, leave the magnet at the rounded edge for 10s.

    4. A long LED signal indicates success.

    Please note that this is a user manual Der Aufpasser from iamsmart is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Der Aufpasser and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.