The following is an overview of the user manual for the Z-Wave product Fan & Light Switch (LZW36)from Inovelli. To view other Z-Wave products and manuals from Inovelli follow that link.
Overview
Security
As a Z-Wave Plus certified product, Fan & Light Switch supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Inovelli describes Fan & Light Switch as having the following features:
- Z-Wave Scene Type
- Electric Load Type
- Firmware updatable via a compatible Z-Wave gateway
- Neutral Wire Required
- Color
- Switch Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Please see Page 9 of our Manual. It will literally be like writing a thesis statement.
N/A
Configuration/Favorites Buttons: This switch allows for ultimate customization via the Configuration Buttons (rather than via a Z-Wave HUB) such as changing the dimming speed, fan speed, minimum/maximum dim level, invert switch, default dim level (local & Z-Wave), the power on state, LED Indicator Color, LED Indicator Intensity, and LED Indicator Intensity (When Off). In addition, the config button doubles as a favorites button allowing you to create your favorite scene (Z-Wave Central Scene) and press the config/favorite button to activate it.
LED Bar Notifications: The LED Bar will alert you when an action has taken place (ie: Door is unlocked after 10pm, your switch will light up Red or your alarm panel is armed, it can flash green, etc).
Central Scene Control: Allows up to 11 different scenes to be added to your switch (10x on the Paddles, 1x on the Config/Favorites Button). A use-case would be: Double Tap down on the switch to activate a bedtime scene that turns off all smart lights, locks the doors, and sets the temperature to 68.
Smart Bulb Compatible: The internal relay can be disabled allowing for full control of Smart Bulbs (Z-Wave bulbs preferred for maximum control). This fixes the issue of when someone flips a switch and turns off power to your smart bulb (causing it to go offline). Now, you can disable the internal relay and send a scene command to turn on/off your bulb. Or directly associate the switch to the bulb to dim up/down and send a scene command to change the colors.
OTA (Over-the-Air) Enabled: As with all our devices, the dimmer allows you to receive our latest firmware updates (NOTE: Please make sure your HUB supports this).
SmartStart location
SmartStart QR code's location as follows: The QR Code can be found on the front of the switch.
Put your hub/gateway into inclusion mode and hold down Button A (top of the config button -- normally used to dim up on the lights) and press Button B (light button) three (3) times. If you've successfully entered inclusion, the LED bars will pulse blue. Once included to the network, the LED bars will flash GREEN (they will flash RED if unsuccessful).
Put your hub/gateway into exclusion mode and hold down Button A (top of the config button -- normally used to dim up on the lights) and press Button B (light button) three (3) times. If you've successfully entered exclusion, the LED bars will pulse blue. Once excluded to the network, the LED bars will flash GREEN (they will flash RED if unsuccessful).
Factory reset Fan & Light Switch
You may hold the Light Level Button (A) + Light On/Off Button (B) for 20 seconds or use a certified controller to remove the device from your network to factory default. Only use this procedure in the event that the network primary controller is missing or otherwise inoperable.
Please note that this is a user manual Fan & Light Switch from Inovelli is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Fan & Light Switch and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.