Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

0-10V In-Wall Smart Dimmer (ICP) (120/277) (43105 / ZW3014) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product 0-10V In-Wall Smart Dimmer (ICP) (120/277) (43105 / ZW3014)from Jasco. To view other Z-Wave products and manuals from Jasco follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
0-10V In-Wall Smart Dimmer (ICP) (120/277)
SKU Code
43105 / ZW3014
Description
0-10V In-Wall Smart Dimmer with QuickFit and SimpleWire enhancements. Revolutionary QuickFit design features a housing depth that is up to 20 percent smaller than the previous Z-Wave models. This reduced size coupled with the elimination of heat taps provides a better fit in older style boxes and multi-gang configurations. SimpleWire technology allows line and load to automatically be configured with auto-sensing line-load terminals. This device includes low voltage wiring designs for use with 0-10V commercial lighting. All of this is coupled with Z-Wave S2 and Smart Start allows for effortless installation while being safer than ever!
Version #
HW: 255 FW: 5.52 was the version certified
Certification #
ZC10-20096972
Certified
2020-09-16T10:10:14.525011
Z-Wave Version
6.82.00

Security

As a Z-Wave Plus certified product, 0-10V In-Wall Smart Dimmer (ICP) (120/277) supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated

Features

Jasco describes 0-10V In-Wall Smart Dimmer (ICP) (120/277) as having the following features:

  • Switch Type
  • Z-Wave Scene Type
  • Firmware updatable via a compatible Z-Wave gateway
  • Neutral Wire Required
  • Switch Load Capacity Volt-Ampere
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press up and release the top or bottom of the rocker.
3. The controller’s app will indicate if it has discovered the switch. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code.

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press up and release the toggle.

Factory reset 0-10V In-Wall Smart Dimmer (ICP) (120/277)

Quickly press ON (up) button three times then immediately press the OFF (down) button three times.

Please note that this is a user manual 0-10V In-Wall Smart Dimmer (ICP) (120/277) from Jasco is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have 0-10V In-Wall Smart Dimmer (ICP) (120/277) and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.