Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S (56590/56592/ZW3012) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S (56590/56592/ZW3012)from Jasco. To view other Z-Wave products and manuals from Jasco follow that link.

Overview
Security
Features
Installation instructions

Overview

Name

Jasco Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S

SKU Code

56590/56592/ZW3012

Description

Transform any home into a smart home with the Enbrighten Z-Wave Smart No-neutral Dimmer. The In-Wall Smart No-neutral Dimmer can easily replace any standard in-wall switch (No-neutral required) and remotely controls a light in your home. Your home will be equipped with ultimate flexibility with the Enbrighten Z-Wave Smart No-neutral Dimmer, capable of being used by itself or with up to four add-on switches. Screw terminal installation provides improved space efficiency when replacing existing switches and the integrated LED indicator light allows you to easily locate the switch in a dark room. The Enbrighten Z-Wave In-Wall Smart No-neutral Dimmer is compatible with any Z-Wave certified gateway, providing access to many popular home automation systems. Take control of your home lighting with Enbrighten Z-Wave Smart Lighting Controls!

Version #

HW: 1 FW: 7.06 was the version certified

Certification #

ZC12-21060235

Certified

2021-06-03T17:10:50.052603

Z-Wave Version

7.13.6

Security

As a Z-Wave Plus certified product, Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S supports Z-Wave S2 security. The following security modes are directly supported:

S2 Authenticated
S2 Unauthenticated

Features

Jasco describes Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S as having the following features:

Firmware updatable via a compatible Z-Wave gateway
Switch Load Capacity Current
Switch Type
Z-Wave Scene Type
FLiRS capable
Supports Network Wide Inclusion
Supports Z-Wave Explorer Frames
Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1).

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press and release the top or bottom of the smart dimmer (rocker).

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press and release the top or bottom of the smart dimmer (rocker).

Factory reset Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S

1. Quickly press ON (top) button three times, then immediately press the OFF (bottom) button three times. The LED will flash ON/OFF five times when completed successfully.

Please note that this is a user manual Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S from Jasco is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Plus In-Wall Smart Dimmer, No Neutral, LED-CFL, White and Light Almond Paddles, 700S and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.

Categories