Leak Gopher Z-Wave Leak Detector (LGZWLD) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Leak Gopher Z-Wave Leak Detector (LGZWLD)from Leak Intelligence, LLC. To view other Z-Wave products and manuals from Leak Intelligence follow that link.

1. Overview
2. Security
3. Features
4. Installation instructions

Overview

Security

As a Z-Wave Plus certified product, Leak Gopher Z-Wave Leak Detector supports Z-Wave S2 security. The following security modes are directly supported:

• S2 Unauthenticated

Features

Leak Intelligence describes Leak Gopher Z-Wave Leak Detector as having the following features:

• Battery Quantity
• Battery powered using Cr123A batteries
• Color
• Firmware updatable via a compatible Z-Wave gateway
• Supported Notification Types
• FLiRS capable
• Supports Network Wide Inclusion
• Supports Z-Wave Explorer Frames
• Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

Factory reset Leak Gopher Z-Wave Leak Detector

Reset to Factory Defaults
How to reset the Leak Gopher Z-Wave Leak Detector
- If the exclusion process above is not working or the Z-Wave controller was lost or not available, the following process can be used to factory reset the device to the same state it has when shipped new.
- To reset the Leak Gopher Z-Wave Leak Detector Z-Wave radio and routing tables, press and HOLD the Z-Wave button for 15 seconds. The LED will blink very quickly while holding the Z-Wave button down. Once the LED turns off, release the Z-Wave button.

Z-Wave Inclusion
How to Add the Leak Gopher Leak Detector to your Z-Wave Controller
- Plug the wall cube power adapter (included) into the receptacle on the bottom of the Leak Gopher Z-Wave Valve Control marked “5 VDC”. Plug the wall cube into a 110 VAC outlet.
This provides power to the Leak Gopher Z-Wave Leak Detector.
- Configure the Z-Wave Controller to Include/Add a device.
- When the Z-Wave Controller is ready to include/add a device, it will display a message like “waiting to add device”. Press and release the Z-Wave button on the front of the LGZWLD.
- The Z-Wave Controller will acknowledge that the LGZWLD has been added to the Z-Wave network.
- Your Leak Gopher Z-Wave Leak Detector is ready to use.
Inclusion without Security
If your home automation hub is does not support the Z-Wave Security Command class, tap the Z-Wave button two times. Tapping the button twice will send a simpler message to the hub which will not include the security command classes.
Inclusion Legacy Mode
If your home automation hub does not support the Z-Wave Notification Command Class, the LGZWLD can substitute the simpler Binary Switch command class. To enable Legacy Mode, tap the Z-Wave button three times during inclusion. Virtually all hubs support the Binary Switch command class.

Z-Wave Exclusion
How to Remove the Leak Gopher Z-Wave Leak Detector from your Z-Wave Controller
- Plug the wall cube power adapter (included) into the receptacle on the bottom of the Leak Gopher Z-Wave Valve Control marked “5 VDC”. Plug the wall cube into a 110 VAC outlet.
This provides power to the Leak Gopher Z-Wave Valve Control.
- Configure the Z-Wave Controller to Exclude a device.
- When the Z-Wave Controller is ready to exclude a device, it will display a message like
“waiting to exclude device”. Press and release the Z-Wave button on the LGZWLD
- The Z-Wave Controller will acknowledge that the LGZWLD has been excluded from the Z-Wave network.
- Your Leak Gopher Z-Wave Leak Detector is excluded from this controller.

Please note that this is a user manual Leak Gopher Z-Wave Leak Detector from Leak Intelligence, LLC is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Leak Gopher Z-Wave Leak Detector and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.