The following is an overview of the user manual for the Z-Wave product 1000W Dimmer (DZ1KD)from Leviton Manufacturing, Inc.. To view other Z-Wave products and manuals from Leviton follow that link.
Overview
Security
As a Z-Wave Plus certified product, 1000W Dimmer supports Z-Wave S2 security. The following security modes are directly supported:
Features
Leviton describes 1000W Dimmer as having the following features:
- Color
- Electric Load Type
- Firmware updatable via a compatible Z-Wave gateway
- Switch Load Capacity Watts
- Neutral Wire Required
- Switch Type
- Z-Wave Scene Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
When removing a device from a Z-Wave® network best practice is to use the exclusion command found in the Z-Wave® controller.
• Enter Programming Mode by holding the top of the paddle for 7 seconds, the Locator LED will blink amber.
• Follow directions in the Z-Wave® controller to enter exclusion mode
• Tap the top of the paddle one time. The Locator LED will quickly flash green.
The Z-Wave® controller will exclude the Decora Smart™ device
• The Z-Wave® controller will confirm successful exclusion from the network.
Leviton Decora Smart™ Z-Wave® devices support two methods of inclusion. When using a Z-Wave Plus® certified controller choose Network Wide Inclusion.
Network Wide Inclusion:
Network Wide Inclusion allows your device to be included into the network using devices already in the network to assist with communication. Work your way from the closest devices to the controller outward.
• Enter Programming Mode by holding the top of the paddle for 7 seconds, the Locator LED will blink amber.
• Tap the top of the paddle one time.
The Locator LED will quickly flash green.
• The Decora Smart™ Z-Wave® device is ready to learn into the Z-Wave® network.
• Follow directions in the Z-Wave controller to complete the adding process.
• Upon successful addition to network the LED will turn off and then blink green 3 times.
• If the adding process is not successful the LED will flash red 3 times.
Traditional Inclusion:
For older controllers Traditional Inclusion is supported. Depending on the age of the controller the controller will need to be 3 to 35 feet from the device when including.
• Enter Programming Mode by holding the top of the paddle for 7 seconds, the Locator LED will blink amber.
• The Decora SmartTM Z-Wave® device is ready to add to the Z-Wave® network.
• Follow directions in the Z-Wave® controller to enter learn mode.
• Tap the top of the paddle one time. The Locator LED will quickly flash green. The Z-Wave® controller will begin to pair with the Decora Smart™ device.
• Upon successful addition to the network the LED will turn off and then blink green 3 times.
• If the adding process is not successful the LED will flash red 3 times.
Factory reset 1000W Dimmer
When removing a device from a network it is best practice to use the Exclusion process. In situations where a device needs to be returned to factory default follow the following steps. A reset should only be used when a controller is inoperable or missing.
• Hold the top of the paddle for a total of 14 seconds.
• After the first 7 seconds the LED turns amber.
• The Locator LED will quickly flash red/amber after 14 seconds.
• Release the top of the paddle and the device will reset.
Please note that this is a user manual 1000W Dimmer from Leviton Manufacturing, Inc. is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have 1000W Dimmer and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.