The following is an overview of the user manual for the Z-Wave product Zula U (HZ61200)from Master. To view other Z-Wave products and manuals from Master follow that link.
Overview
Security
As a Z-Wave Plus certified product, Zula U supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Master describes Zula U as having the following features:
- Color
- Communications Protocol
- Electric Load Type
- Neutral Wire Required
- Outdoor Use
- Switch Load Capacity Current
- Switch Load Capacity Watts
- Switch Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: When adding the Zula to a Z-Wave network with a controller supporting Security 2 (S2), the PIN code of the Z-Wave Device Specific Key (DSK) is required. The unique DSK code is printed on the product label and a copy is inserted in the packaging, which must not be lost. Do not remove the DSK from the product.
The first five digits of the key are highlighted or underlined to help the user identify the PIN code portion of the DSK text.
The DSK is additionally represented with a QR Code as shown here.
AUTOMATICALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (AUTO INCLUSION)
1. Enable add/remove mode on your Z-Wave gateway (hub).
2. Connect the device to the power supply.
3. The device can be automatically added to a Z-Wave network during the first 2 minutes after being connected to power supply.
4. Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will automatically enroll in your network. (when the device is excluded and connected to the power supply it automatically enters the LEARN MODE state.)
ⓘ NOTE: LEARN MODE state allows the device to receive network information from the controller
ⓘ NOTE: For S2 inclusion please check chapter – »8.3 Z-Wave Security and DSK«.
MANUALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (MANUAL INCLUSION)
1. Connect the device to the power supply
2. Enable add/remove mode on your Z-Wave gateway (hub)
3. Toggle the switch connected to the terminal I 3 times within 3 seconds (this procedure puts the device in LEARN MODE). The device has to get On/Off signal 3 times, meaning 3 times push of the momentary switch or with toggle switch 3 times On and 3 times Off.
OR
Press and hold the S (Service) button between 2 and 6 seconds if connected to power supply. For your safety use only 24-30 Vdc power supply when accessing to S (Service) button. This procedure puts the device in LEARN MODE.
4. A new device will appear on your dashboard.
5. Inclusion with the switch connected to terminal I is not limited by time.
ⓘ NOTE: LEARN MODE state allows the device to receive network information from the controller.
REMOVAL FROM A ZWAVE NETWORK (Z-WAVE EXCLUSION)
1. Connect the device to the power supply.
2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion.
3. Enable add/remove mode on your Z-Wave gateway (hub).
4. Toggle the switch connected to the terminal I 3 times within 3 seconds (this procedure put the device in LEARN MODE). The device has to get On/Off signal 3 times, meaning 3 times push of the momentary switch or with toggle switch 3 times On and 3 times Off.
OR
Press and hold the S (Service) button between 2 and 6 seconds if connected power supply. For your safety use only 24-30 Vdc power supply when accessing to S (Service) button. This procedure put the device in LEARN MODE.
5. Exclusion with the switch connected to terminal I is not limited by time.
6. The device will be removed from your network, but any custom configuration parameters will not be erased.
ⓘ NOTE: LEARN MODE state allows the device to receive network information from the controller.
Factory reset Zula U
1. Connect the device to the power supply.
2. Within the first minute (60 seconds) the device is connected to the power supply, toggle the switch connected to the terminal I 5 times within 3 seconds. The device has to get On/Off signal 5 times, meaning 5 times push of the momentary switch or with toggle switch 5 times On and 5 times Off.
OR
Press and hold the S (Service) button for at least 6 seconds if connected to power supply. For your safety use only 24-30 Vdc power supply when accessing to S (Service) button. This procedure put the device in LEARN MODE.
ⓘ NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the node ID will be deleted. Use this reset procedure only when the main gateway (hub) is missing or otherwise inoperable.
ⓘ NOTE: the reset with switch connected to terminal I is possible only in the first minute after the device is connected to the power.
ⓘ NOTE: after the reset is successfully done the autocalibration will trigger and the green LED will start blinking.
Please note that this is a user manual Zula U from Master is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Zula U and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.