The following is an overview of the user manual for the Z-Wave product [rg3+] (mob.iq [rg3+])from MOB.IQ. To view other Z-Wave products and manuals from MOB.IQ follow that link.
Overview
Remote controller mob.iq [rg3+] combines a contemporary, minimalist form, intuitive operation and advanced control technology. Users can open gates, raise blinds, close awnings, turn on lights, and activate predefined settings of different receivers. The simplicity of the control system provides instant access to individual devices.
Mob.iq [rg3+] is the controller which allows to configure and control every device in Z-Wave network which is up to 231 devices. In order to improve the user experience devices may be gathered into a group and be freely situated in 4 groups. Devices in each group can be controlled simultaneously. Remote controller mob.iq [rg3+] may be a primary, secondary or inclusion. Primary controller allows the integration and configuration of many devices in radio network, secondary fulfils a function of additional controller in already existing network and finally, inclusion controller fulfils a function of additional controller capable to maintain network in already existing network with Z-Wave gateway. Next to the primary control procedure which is: OPEN, STOP, CLOSE remote controller mob.iq [rg3+] also possesses multilevel procedure which allows for example to dim a light smoothly.
Security
As a Z-Wave Plus certified product, [rg3+] supports Z-Wave S2 security. The following security modes are directly supported:
Features
MOB.IQ describes [rg3+] as having the following features:
- Controller Supports Multiple Z-Wave Interfaces
- Battery Quantity
- Battery powered using CR2450 batteries
- Controller Supports Multiple Networks
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Factory reset [rg3+]
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Restoring controller to factory settings removes from its memory all data about Z-Wave network, which means it will forget all added devices and return to PRIMARY CONTROLLER state. To reset controller to factory settings, proceed as follows:
1. Simultaneously press and hold STOP and DOWN button until the LEDs light red.
2. Left channel LED flashes green.
3. Using right navigation key , select all channel LED .
4. Confirm the choice with STOP button.
5. All channel LEDs turns on solid and the red LEDs are off.
6. A successfully completed operation will be signaled by controller through single blink of green LEDs .
In one Z-Wave network can be only one PRIMARY CONTROLLER. If the customer wants to have another controller in the same network, it must be added to it by calling learn mode. After this, controller will become SECONDARY or INCLUSION CONTROLLER. In order to call learn mode proceed as follows.
1. Call include mode on controller to which mob.iq [ RG3+] controller is to be added.
2. Simultaneously press and hold STOP and DOWN button until the LEDs light red.
3. Left channel LED flashes green.
4. Confirm the choice with STOP button.
5. Left channel LED turns on solid and the red LEDs are off.
6. A successfully completed operation will be signaled by controller through single blink of green LEDs, if the operation in not successfully completed, the controller will signal it through a triple blink of red LEDs .
Learn mode has a built-in timeout which will abort learn mode if controller does not receive any information in 5 seconds after learn mode started.
If the controller to which mob.iq [ RG3+] controller was added supports controller replication, then mob.iq [ RG3+] controller will transfer all information about added devices and groups to the other controller (then associating devices will not be necessary).
If you want to remove the device from the Z-Wave network (it can be any Z-Wave network) perform the exclude function. In order to remove the device from network, proceed as follows:
1. Simultaneously press and hold STOP and DOWN button until the LEDs light red.
2. Left channel LED flashes green .
3. Using right navigation key , select the right channel LED.
4. Confirm the choice with STOP button.
5. Right channel LED turns on solid and the red LEDs are off.
6. Press the programming button on the device working in the mob.iq system (for example blind) - device should send NIF.
7. A successfully completed operation will be signaled by controller through single blink of green LEDs, if the operation in not successfully completed, the controller will signal it through a triple blink of red LEDs.
Exclude operation has a built-in timeout which will abort exclusion mode if controller does not receive NIF in 60 seconds after exclusion mode started.
In order to operate the electrical accessories using mob.iq [ RG3+] controller, the devices working in the mob.iq system must be added to the mob.iq [ RG3+] remote. Quick start operation performs inclusion of device into the network and assigns it into all association groups assigned to current channel. Please proceed as follows.
1. Using navigation keys select the channel on which the Z-Wave device is to be added.
2. Simultaneously press and hold STOP and UP button until the LEDs light green.
3. Left channel LED flashes green (when the middle LED flashes green, it means that controller is SECONDARY CONTROLLER) .
4. Confirm the choice with STOP buton.
5. Left channel LED turns on solid and the green LEDs are off.
6. Press the programming button on the device working in the mob.iq system ( for example blind ) - device should send NIF.
7. A successfully completed operation will be signaled by controller through single blink of green LEDs, if the operation in not successfully completed, the controller will signal it through a triple blink of red LEDs.
Quick start operation has a built-in timeout which will abort inclusion mode if controller does not receive NIF in 60 seconds after inclusion mode started.
In Z-Wave network it is possible to remotely exchange data with another controller in network. To call this function, proceed as follows:
1. Simultaneously press and hold STOP and UP button until the LEDs light green.
2. Left channel LED flashes green ( when the middle LED flashes green, it means that controller is SECONDARY CONTROLLER).
3. Using right navigation key , select all channel LEDs.
4. Confirm the choice with STOP button.
5. All channel LEDs turn on solid and the green LEDs are alternating in clockwise direction .
6. Controller is in data exchange mode - mode is turned on for 60 seconds and the function is renewed after each data exchange request but it is possible to quit this mode by pressing STOP once.
Please note that this is a user manual [rg3+] from MOB.IQ is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have [rg3+] and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.