Radio Switch Dual Plus (MTSWI-101-WL) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Radio Switch Dual Plus (MTSWI-101-WL)from myTEM SmartHome. To view other Z-Wave products and manuals from myTEM SmartHome follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Radio Switch Dual Plus
SKU Code
MTSWI-101-WL
Description
The myTEM Radio Switch Dual Plus is a universal, Z-Wave compatible wall or ceiling switch (ON/OFF) and is used to control two electrical devices. Two additional digital inputs and the programmable behav-ior to the wireless commands allow flexible use in the house. Optionally, a myTEM Touch Add-on control panel can be attached to the connector.
The device is intended for installation in a flush-mounted box.
Version #
HW: 1 FW: 1.00 was the version certified
Certification #
ZC10-19076686
Certified
2019-05-23T20:11:59.536299
Z-Wave Version
6.71.03

Security

As a Z-Wave Plus certified product, Radio Switch Dual Plus supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated

Features

myTEM SmartHome describes Radio Switch Dual Plus as having the following features:

  • Switch Load Capacity Watts
  • Switch Type
  • Electric Load Type
  • Firmware updatable via a compatible Z-Wave gateway
  • Loads Controlled
  • Sensors
  • Supported Notification Types
  • Switch Load Capacity Current
  • Color
  • Switch Load Capacity Volt-Ampere
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

Manual exclusion (“Remove”)
1. Activate the “Remove” mode on your controller.
2. When 110 – 230 VAC is used, press a button connected to input I1 or I2 four times in quick succession to start exclude (“Remove”). If a switch is used instead of the button, it must be changed accordingly eight times.
3. Alternatively, when 24 VDC is used, you can press the small lever (T) four times in quick succession with a pen to start “Remove”.
When finished, the new status is:
Add: The LED lights up briefly in green
Remove: The LED lights up briefly in red

Automatic inclusion (“Add”)
The device supports the so-called auto-inclusion. To use this function the device must be in factory default.
1. Activate the “Add” mode on your controller.
2. Turn on the power and the unit starts in its own Add mode for 30 seconds. If the connection is successful, the device registers on the controller.
When the device is in the “Add” mode, the LED flashes green. When finished, the new status is:
Add: The LED lights up briefly in green
Remove: The LED lights up briefly in red.

Manual inclusion (“Add”)
1. Activate the “Add” mode on your controller.
2. When 110 – 230 VAC is used, press a button connected to input I1 or I2 four times in quick succession to start include (“Add”). If a switch is used instead of the button, it must be changed accordingly eight times.
3. Alternatively, when 24 VDC is used, you can press the small lever (T) four times in quick succession with a pen to start “Add”.
When the device is in the “Add” mode, the LED flashes green. When finished, the new status is:
Add: The LED lights up briefly in green
Remove: The LED lights up briefly in red

Factory reset Radio Switch Dual Plus

Reset to factory default
If the myTEM Radio Switch Dual Plus shows status “Add”, the “Remove” can be performed with any controller in the network or with the help of a new controller. However it is recommended to use the primary controller of the previous network unless it is no longer available or damaged.
“Remove” deletes the memory chip, including all Z-Wave network and custom configuration settings.

Please note that this is a user manual Radio Switch Dual Plus from myTEM SmartHome is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Radio Switch Dual Plus and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.