The following is an overview of the user manual for the Z-Wave product Scene Controller (ZA-207001)from Ness. To view other Z-Wave products and manuals from Ness follow that link.
Overview
Security
As a Z-Wave Plus certified product, Scene Controller supports Z-Wave S2 security. The following security modes are directly supported:
Features
Ness describes Scene Controller as having the following features:
- Battery powered using LIR2450 batteries
- Battery Quantity
- Z-Wave Scene Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Included as non-secure device:
1. Insert the LIR2450 battery.
2. Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).
3. Triple click a button.
4. If the inclusion is successful, the LED will blink in blue less than for 5 seconds and then keep on for 15 seconds.
Included as a secure device:
1. Insert the LIR2450 battery.
2. Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).
3. Pressing and holding a button for 3 seconds.
4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds.
To remove the Scene Controller from the Z-Wave network:
(1) Insert the LIR2450 battery.
(2) Set the Z-Wave network main controller into remove mode
(see Z-Wave controller operating manual).
(3) Triple click the a button, if the exclusion is successful, LED
will blink in orange for less than 5 seconds and then keep on
for 3 seconds.
To remove the Scene Controller from the Z-Wave network:
(1) Insert the LIR2450 battery.
(2) Set the Z-Wave network main controller into excluding mode
(see Z-Wave controller operating manual).
(3) Triple click the Z-button, if the exclusion is successful, LED will blink
in orange for less than 5 seconds and then keep on for 3 seconds.
Scene Controller's LED indicator can signal its communication quality
with the Z-Wave main controller.
To start testing:
Press and hold the Z-button for 11 to 15 seconds, the LED will keep on
in purple for 3 seconds, it will enter testing mode if you short press the
Z-button during these 3 seconds.
Blink in green –Scene Controller establish a direct communication with
the main controller, and still under checking.
Keep green – The green light should last about 2 seconds, which means
the direct communication is stable.
Blink in orange –Scene Controller can communicate with the main
controller in intermediate radio transmit power level, and still under
checking.
Keep orange – The communication quality is moderate.
Keep Red – The communication is failed.
Included as a non-secure device
(1) Insert the LIR2450 battery.
(2) Set the Z-Wave network main controller into learning mode
(see Z-Wave network controller operating manual).
(3) Triple click the Z-button.
(4) If the inclusion is successful, the LED will blink in blue less than
for 5 seconds and then keep on for 15 seconds.
Included as a secure device
(1) Insert the LIR2450 battery.
(2) Set the Z-Wave network main controller into learning mode
(see Z-Wave network controller operating manual).
(3) Pressing and holding the Z-button for 3 seconds.
(4) If the inclusion is successful, the LED will blink in green less than
for 5 seconds and then keep on for 15 seconds.
Pressing and holding a button for 3 seconds. Led will turn to green,
which means Scene Controller has been woken up.
Factory reset Scene Controller
Pressing and holding a button for 20 seconds. Release the button after 20 seconds, LED will keep in yellow for 3 seconds. Scene Controller will be reset to factory defaults if you short press the button within this 3 seconds.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Please note that this is a user manual Scene Controller from Ness is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Scene Controller and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.