The following is an overview of the user manual for the Z-Wave product Heat-Control (FGT-001)from Nice. To view other Z-Wave products and manuals from Nice follow that link.
Overview
It can be mounted without tools on three types of thermostatic radiator valves.
You can create schedules via app to easily manage temperature throughout the week.
Security
As a Z-Wave Plus certified product, Heat-Control supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Nice describes Heat-Control as having the following features:
- Thermostat Modes
- Thermostat Power Source
- Thermostat HVAC Systems Supported
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: Security DSK 2 - you can find on packing label
1. Make sure the device is within the direct range of your Z-Wave controller.
2. Set the main controller into remove mode (see the controller’s manual).
3. Quickly triple click the button on the thermostatic head.
4. The LED ring will start blinking white.
5. Wait for the removing process to end.
6. Successful removing will be confirmed by the Z-Wave controller and red LED colour.
To add the device to the Z-Wave network manually:
1. Make sure the device is within the direct range of your Z-Wave controller.
2. Set the main controller in (security/non-security) add mode (see the controller’s manual)
3. Quickly triple click the button on the thermostatic head.
4. The LED ring will start blinking white.
5. If you are adding in S2 authenticated mode, type in the device pin code (underlined part of the public key on the label).
6. Wait for the adding process to end.
7. Successful adding will be confirmed by the Z-Wave controller and green LED colour.
Factory reset Heat-Control
To perform factory reset:
1. Press and hold the button.
2. Release the button when you see yellow LED colour.
3. Click the button to confirm the selection.
4. After finishing resetting the device will be put in Standby Mode. Click the button to activate it again.
f you use one of the adapters, double check that it is mounted properly. It should click when putting on the valve, hold tight
after installing and not rotate!
• If the device is installed in vertical position, set bit 5 in parameter 2.
• Do not cover or veil the thermostatic head.
• First charging may take up to 3 hours.
1. Connect the charger to the micro-USB port to charge the device. The LED ring will pulse red if it’s not fully charged; otherwise, it will pulse
green.
If you have the temperature sensor:
• Use a coin to open the battery cover by turning it counter-clockwise.
• Remove the sticker underneath the battery.
• Use a coin to close the battery cover by turning it clockwise.
2. Disconnect the charger when the LED ring pulses green (device fully charged).
3. Dismount your current thermostatic head.
4. Depending on type of your thermostatic valve:
M30 x 1.5
Danfoss RTD-N
Danfoss RA-N
Proceed normally
Use adapter:
Use adapter:
5. Mount the device on the valve and tighten it by turning the cap clockwise.
6. Press and hold the button for at least one second. The LED ring will start blinking blue.
If you have the temperature sensor:
1) Click the button on the temperature sensor now.
2) The LED ring on the thermostatic valve will blink green 5 times if the connection was successful.
Please note that this is a user manual Heat-Control from Nice is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Heat-Control and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.