OCTAN Remote (CRC-3-1-0X) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product OCTAN Remote (CRC-3-1-0X)from NodOn. To view other Z-Wave products and manuals from NodOn follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
OCTAN Remote
SKU Code
CRC-3-1-0X
Description
The OCTAN Remote NodOn® controls any compatible receivers Z-Wave® or Z-Wave Plus®, such as the Smart Plug NodOn®. It can address, directly, up to 4 groups of 8 devices and sent up to 16 different scenes to a Home Automation Gateway. This controller can operate on its own (“Standalone” Mode) or as gateway’s assistant (“Gateway” Mode). The product integrates a LED, which give an intuitive feedback for each operation you perform.

Based on an innovative technology, the OCTAN Remote NodOn® is only powered with a CR2032 battery, offering 2 years’ autonomy.

A magnetic wall support is included with your OCTAN Remote NodOn®, which allow you to easily install and move it. This support can be screwed or fixed by adhesive bonding. The remote control embeds a small magnet, allowing fixing it on its wall support or on any metallic surface (fridge door, heater, etc.).

The OCTAN Remote NodOn® is based on brand new 500 series Z-Wave® module from Sigma Designs®, and supports all the new features of Z-Wave Plus® standard:
Longer range (up to 40 meters indoor), lower power consumption, higher data rate transmission, and many more new features.
Version #
02 was the version certified
Certification #
ZC10-15060001
Certified
2015-06-04T06:57:43.6836
Z-Wave Version
6.51.06

Security

As a Z-Wave Plus certified product, OCTAN Remote supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    NodOn describes OCTAN Remote as having the following features:

    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    1- Push 3 times (quickly) on the button 3. The LED blinks in blue.

    2- Place the device you want to add in “Learning” Mode. To do so, please refer to your device’s user guide. The LED blinks in green to confirm the inclusion.

    Note: If you wish to include and associate a device, please refer to ""Other Special Features""

    1- Push 3 times (quickly) on the button 2. The LED blinks in blue.

    2- Place the device you want to remove in “Learning” Mode. To do so, please refer to your device’s user guide. The LED blinks in green to confirm the exclusion.

    1- Place your home automation gateway into “Inclusion” Mode. To do so, please refer to your gateway’s user guide.

    2- Simultaneously push on buttons 1 and 2, during 1 second. The LED glows in pink to confirm the selection.

    3- Push on button 1. The LED blinks in pink to confirm your choice.

    4- The LED blinks in green to confirm the procedure

    When the product in ""Gateway"" mode, any action on button will send a wake up notification to the gateway.

    Factory reset OCTAN Remote

    Simultaneously push on buttons 3 and 4, during 1 second. The LED will blink red and green to validate the factory reset.

    A factory reset will completely delete the memory of the remote control and restore all parameters to default value.
    In ""Standalone"" Mode, make sure to remove all the devices added or associated in the remote control's network before performing a factory reset.
    In ""Gateway"" Mode, use the factory reset procedure only when the primary controller (i.e the Gateway) is missing or defective. Reset the remote control does not mean that it has been removed from the primary controller memory. Remove the remote control (through the primary controller) before performing a factory reset.

    Association, in ""Standalone"" mode is performed in 3 steps:

    1- Push 3 times (quickly) on the button 1 to activate the ""Association” Mode. The LED glows in blue.

    2- Choose which button will control your device.
    • A short press on one of the buttons of the remote control (1, 2, 3 or 4) will activate the MONO Profile. The pressed button will then control your device.
    • A long press on the button 1 will activate the DUO Profile, combined with the button 3. The button 1 (ON) and button 3 (OFF) will then control your device.
    • A long press on the button 2 will activate the DUO Profile, combined with the button 3. The button 2 (ON) and button 4 (OFF) will then control your device.
    The LED blinks in blue to confirm your choice.

    3-Place the device you want to associate in “Learning” Mode. To do so, please refer to your device’s user guide. The LED of the remote control blinks green to confirm the association process

    Careful: In case of a too long association process or others problems during the process, the LED will blink red (Timeout). Please restart the procedure.

    Once the association is validated, your remote control is able to control your device. Different actions are possible.

    Please note that this is a user manual OCTAN Remote from NodOn is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have OCTAN Remote and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.