Recessed Door Sensor (PSM09-A) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Recessed Door Sensor (PSM09-A)from Philio. To view other Z-Wave products and manuals from Philio follow that link.

Overview
Security
Features
Installation instructions

Overview

Name

Recessed Door Sensor

SKU Code

PSM09-A

Description

PSM09 is only for indoor using device. PSM09 can detect the the door is open or not. The Recessed door sensor PSM09 is Base on Z-WaveTM technology. It is the Z-WaveTM plus product, it support the security, OTA. Those newest features of the Z-WaveTM technology. Z-WaveTM is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances. Notice: if user use some command, it have to check device is security bootstrap otherwise some command cannot increment. This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products. This device must be used in conjunction with a Security Enabled Z-Wave Controller in order to fully utilize all implemented functions. This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

Version #

HW: 255 FW: 0.10 was the version certified

Certification #

ZC10-19066570

Certified

2019-06-28T04:21:32.058987

Z-Wave Version

6.81.04

Security

As a Z-Wave Plus certified product, Recessed Door Sensor supports Z-Wave S2 security. The following security modes are directly supported:

S2 Unauthenticated

Features

Philio describes Recessed Door Sensor as having the following features:

Sensors
Firmware updatable via a compatible Z-Wave gateway
Supported Notification Types
Battery Quantity
Battery powered using ER14250 batteries
FLiRS capable
Supports Network Wide Inclusion
Supports Z-Wave Explorer Frames
Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

Check Z-WaveTM Controller enter inclusion mode. Pressing tamper key three times within 3 seconds to enter the inclusion mode. If the addition is successful, the LED will flash slowly.

Check Z-WaveTM Controller enter exclusion mode. Pressing tamper key three times within 3 seconds to enter the exclusion mode. If the removal is successful, the code light will flash for 30 seconds.

Factory reset Recessed Door Sensor

Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.
Press the button three times in three seconds, then LED will flash for one second slowly. Press the button again and hold, the LED will light up, after about three seconds, the LED will off. Please release the button in two seconds. If the clearing is successful, the LED will flash one time per second. If it fails, the LED will flash quickly.

After the device adding to the network, it will wake-up once per day in default. When it wake-up it will broadcast the “Wake Up Notification”message to the network, and wake-up 10 seconds for receive the setting commands.
The wake-up interval minimum setting is 30 minutes, and maximum setting is 120 hours. And the interval step is 30 minutes.
If the user want to wake-up the device immediately, please press the tamper key once. The device will wake-up 10 seconds.

Please note that this is a user manual Recessed Door Sensor from Philio is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Recessed Door Sensor and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.

Categories