Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Smart Energy Plug In Switch (PAN11-1B) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Smart Energy Plug In Switch (PAN11-1B)from Philio. To view other Z-Wave products and manuals from Philio follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Smart Energy Plug In Switch
SKU Code
PAN11-1B
Description
This plug-in ON/OFF switch PAN11 is a security enabled wireless switch, based on Z-Wave Plus technology. Z-Wave PlusTM enabled devices displaying the Z-Wave PlusTM logo can also be used with it regardless of the manufacturer, and can also be used in other manufacturer’s Z-WaveTM enabled networks. Remote On/Off control of the connected load is possible with other manufacturer’s wireless Controller. Each switch is designed to act as a repeater. Repeaters will re-transmit the RF signal to ensure that the signal is received by its intended destination by routing the signal around obstacles and radio dead spots. Because PAN11 supports Security Command Class, it can learn with Secured controller. Its functionality and supported command classes is identical when included as a secure and non-secure device.

This plug-in ON/OFF switch is able to detect instance wattage (3000W/CE/CN, 1560W/UL/TW/JP) and overload current (14.5A with resistive load) of connected lights or appliances. When detecting overload state, the Switch will be disabled and its On/Off button will be lockout of which LED will flash quickly. However, unplug and re-connect the switch will reset its overload condition to normal status.

Adding to Z-WaveTM Network

In the front casing, there is an On/Off button with LED indicator which is used to toggle switch on and off or carry out inclusion, exclusion, reset or association. When first power is applied, its LED flashes on and off alternately and repeatedly at 0.5 second intervals. It implies that it has not been assigned a node ID and start auto inclusion.

Auto Inclusion

The function of auto inclusion will be executed as long as the switch does not have Node ID and just plug the switch into a wall outlet.

Note: Auto inclusion timeout is 2 minute during which the node information of explorer frame will be emitted once several seconds. Unlike “inclusion” function as shown in the table below, the execution of auto inclusion is free from pressing the On/Off button on the Switch.
Version #
HW: 1 FW: 1.12 was the version certified
Certification #
ZC10-15125001
Certified
2015-12-11T13:49:56.5164
Z-Wave Version
6.51.06

Security

As a Z-Wave Plus certified product, Smart Energy Plug In Switch supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    Philio describes Smart Energy Plug In Switch as having the following features:

    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.
    2. Pressing On/Off button three times within 2 seconds will enter inclusion mode.

    1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.
    2. Pressing On/Off button three times within 2 seconds will enter exclusion mode.

    Factory reset Smart Energy Plug In Switch

    Use this procedure only in the event that the primary controller is lost or otherwise inoperable.

    1. Pressing On/Off button three times within 2 seconds will enter inclusion mode. Use this procedure only in the event that the primary controller is lost or otherwise inoperable.
    2. Within 1 second, press On/Off button again for 5 seconds.

    Please note that this is a user manual Smart Energy Plug In Switch from Philio is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Smart Energy Plug In Switch and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.