The following is an overview of the user manual for the Z-Wave product IQ Outlet Plug-In On/Off Switch (QZ2130-840)from Qolsys Inc.. To view other Z-Wave products and manuals from Qolsys follow that link.
Overview
Additional Features:
• Works with incandescent, CFL & LED lights & appliances
• Plugs into Standard AC outlet
• Remotely or manually turns ON or OFF lights
• LED backlit On/Off button
• Control lights or appliances via schedule or remotely
• Second wall AC outlet remains free
• Works with any gateway supporting Z-Wave
Security
As a Z-Wave Plus certified product, IQ Outlet Plug-In On/Off Switch supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Qolsys describes IQ Outlet Plug-In On/Off Switch as having the following features:
- Outdoor Use
- Switch Type
- Electric Load Type
- Firmware updatable via a compatible Z-Wave gateway
- Switch Load Capacity Current
- Switch Load Capacity Volt-Ampere
- Switch Load Capacity Watts
- Color
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Factory reset IQ Outlet Plug-In On/Off Switch
1. Unplug the IQ Outlet from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)
2. Press and hold the button on the IQ Outlet
3. Plug the IQ Outlet back into the AC outlet with the button pressed
After 3 seconds, release the button. If you see the button blink, that means that IQ Outlet has been reset successfully.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
The QR code label with DSK can be found on the bottom of the device
Exclusion: Remove the device into your network by a Z-Wave certified controller. The IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on removing devices to the network. In addition, the device can be removed using the traditional method for Z-Wave as follows:
1. Place your network controller into Exclusion mode by following the controller manufacturer's instructions.
2. When the controller is ready, single click the button on the front of the IQ Outlet. The controller should indicate that the new device was removed successfully.
If the controller shows it failed, repeat the procedure.
Inclusion: Add the device into your network by a Z-Wave certified controller. The IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on adding devices to the network. You should be able to add the IQ Outlet into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added using the traditional method for Z-Wave as follows:
1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.
2. When the controller is ready, single click the button on the front of the IQ Outlet. The controller should indicate that the new device was added successfully.
3. Once the IQ Outlet has been successfully added to your home network, you can move it to the preferred location in the home.
If the controller shows it failed, repeat the procedure.
Please note that this is a user manual IQ Outlet Plug-In On/Off Switch from Qolsys Inc. is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have IQ Outlet Plug-In On/Off Switch and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.