3-Phase Smart Meter (ZMNHXD1) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product 3-Phase Smart Meter (ZMNHXD1)from QUBINO. To view other Z-Wave products and manuals from Qubino follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


3-Phase Smart Meter
SKU Code
The Qubino 3 Phase Smart Meter can be used in residential, industrial and utility applications. It measures energy directly in 2-wire networks by means of fast sampling of voltage and current signals. It calculates energy, power and power factor from the measured signals. You can control the device through the Z-Wave network.
The Qubino 3 Phase Smart Meter can operate across a wide temperature range, from a chilly -15˚C to a scorching 55˚C (5˚F–131˚F). Every device also acts as a repeater in order to improve the range and stability of the Z-Wave network.
Version #
HW: 1 FW: 1.00:01.00 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, 3-Phase Smart Meter supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


Qubino describes 3-Phase Smart Meter as having the following features:

  • Firmware updatable via a compatible Z-Wave gateway
  • Switch Load Capacity Current
  • Loads Controlled
  • Switch Load Capacity Watts
  • IP (Ingress Protection) Rated
  • Supported Meter Type
  • Electric Load Type
  • Communications Protocol
  • Neutral Wire Required
  • Switch Type
  • Color
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

1. Connect the device to the power supply
2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
3. Enable add/remove mode on your Z-Wave gateway (hub)
4. Press and hold the S service button between 0.2 and 3 seconds
5. The device will be removed from your network, but custom configuration parameters will not be erased. Wait at least 30 seconds before attempting to add the device back to a network.

1. Enable add mode on your Z-Wave gateway (hub). Put the device in a mode, in which it can be added to a network (learn mode)
2. Automatic selection of secure/unsecure inclusion
3. The device can be automatically added to a Z-Wave network during the first 2 minutes
4. Connect the device to the power supply
5. Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will be automatically added to your network

1. Connect the device to the power supply
2. Enable add/remove mode on your Z-Wave gateway (hub)
2. Toggle the Service button S between 0.2 and 3 seconds
3. A new multi-channel device will appear on your dashboard

Factory reset 3-Phase Smart Meter

1. Connect the device to the power supply
2. Press and hold the S service button between 6 seconds and 20 seconds
3. Device will be removed from you network and the green LED start blinking

By resetting the device, all previously set parameters on the device will return to their default values, and the Home ID will be deleted. Use this reset procedure only when the main
gateway (hub) is missing or otherwise inoperable.

Please note that this is a user manual 3-Phase Smart Meter from QUBINO is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have 3-Phase Smart Meter and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.