The following is an overview of the user manual for the Z-Wave product Mini Dimmer (ZMNHHD1)from QUBINO. To view other Z-Wave products and manuals from Qubino follow that link.
Overview
Security
As a Z-Wave Plus certified product, Mini Dimmer supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Qubino describes Mini Dimmer as having the following features:
- Communications Protocol
- Color
- Electric Load Type
- Neutral Wire Required
- Outdoor Use
- Supported Meter Type
- Supported Notification Types
- Switch Load Capacity Current
- Switch Load Capacity Watts
- Switch Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
AUTOMATICALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (AUTO INCLUSION)
1. Enable add/remove mode on your Z-Wave gateway (hub)
2. Automatic selection of secure/unsecure inclusion.
3.The device can be automatically added to a Z-Wave network during the first 2 minutes
4. Connect the device to the power supply
5. Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will automatically enrol in your network. (when the device is excluded and connected to the power supply it automatically eneters the LEARN MODE state.)
ⓘ NOTE: LEARN MODE state allows the device to receive network infromation from the controller
ⓘ NOTE: Please wait at least 30 seconds between each inclusion and exclusion.
MANUALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (MANUAL INCLUSION)
1. Connect the device to the power supply
2. Enable add/remove mode on your Z-Wave gateway (hub)
3. Toggle the switch connected to the I1 terminal 3 times within 3 seconds (this procedure put the device in LEARN MODE)
OR
Press and hold the S (Service) button between 2 and 6 seconds if connected to 24-30VDC (this procedure put the device in LEARN MODE)
4. A new device will appear on your dashboard
ⓘ NOTE: LEARN MODE state allows the device to receive network infromation from the conttoller
ⓘ NOTE: Please wait at least 30 seconds between each inclusion and exclusion.
Mini Dimmer supports the latest Security 2 feature. When adding the Mini Dimmer to a Z-Wave network with a controller supporting Security 2 (S2), the PIN code of the Z-Wave Device Specific Key (DSK) is required. The unique DSK code is printed on the product label and a copy is inserted in the packaging, which must not be lost. Do not remove the DSK from the product. As a backup measure, use the label in the packaging. The first five digits of the key are highlighted or underlined to help the user identify the PIN code portion of the DSK text.
REMOVAL FROM A Z-WAVE NETWORK (Z-WAVE EXCLUSION)
1. Connect the device to the power supply
2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
3. Enable add/remove mode on your Z-Wave gateway (hub)
4. Toggle the switch connected to the I1 terminal 3 times within 3 seconds (this procedure put the device in LEARN MODE)
OR
Press and hold the S (Service) button between 2 and 6 seconds if connected to 24-30VDC (this procedure put the device in LEARN MODE)
5. The device will be removed from your network, but any custom configuration parameters will not be erased
ⓘ NOTE: LEARN MODE state allows the device to receive network infromation from the conttoller
ⓘ NOTE: Please wait at least 30 seconds between each inclusion and exclusion.
Factory reset Mini Dimmer
FACTORY RESET
1. Connect the device to the power supply
2. Within the first minute the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 3 seconds. The reset with switch connected to I1 is possible only in the first minute after the device is connected to the power.
OR
Press and hold the S (Service) button for at least 6 seconds if connected to 24-30VDC
ⓘ NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted. Use this reset procedure only when the main gateway (hub) is missing or otherwise inoperable.
After the reset is successfully done the autocalibration will trigger and the green LED will start blinking.
Please note that this is a user manual Mini Dimmer from QUBINO is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Mini Dimmer and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.