The following is an overview of the user manual for the Z-Wave product Dimming Switch Module (Dual mode) (ZDS-220NA)from Remotec. To view other Z-Wave products and manuals from Remotec follow that link.
Overview
The ZDS-220 is a Z-Wave enabled device and is fully compatible with any Z-Wave Plus enabled network. It can be configured as either a “DIMMER” or a “SWITCH” device. It allows remote Dimming or ON/OFF control of specified lamps. Each module is designed to act as a repeater, which will re-transmit a radio frequency (RF) signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination.
ZDS-220 is a security enabled Z-Wave plus device. A security Enabled Z-Wave Plus Controller must be used in order to fully utilize the product.
Security
As a Z-Wave Plus certified product, Dimming Switch Module (Dual mode) supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Unauthenticated
Features
Remotec describes Dimming Switch Module (Dual mode) as having the following features:
- Color
- Electric Load Type
- Firmware updatable via a compatible Z-Wave gateway
- Switch Load Capacity Watts
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: Not support
Include or exclude the ZDS-220 from the existing Z-Wave home control network with your primary controller.
- Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.
- When prompted by your primary controller, triple click the PROG button within 1 second.
(The unit will enter classical inclusion/exclusion first, then jump to NWI, and after 20 seconds, it will finally exit NWI mode automatically if there is no inclusion/exclusion request.)
- The primary controller should indicate that the action was successful. If the controller indicates the action was unsuccessful, please repeat the procedure.
Include or exclude the ZDS-220 from the existing Z-Wave home control network with your primary controller.
- Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.
- When prompted by your primary controller, triple click the PROG button within 1 second.
(The unit will enter classical inclusion/exclusion first, then jump to NWI, and after 20 seconds, it will finally exit NWI mode automatically if there is no inclusion/exclusion request.)
- The primary controller should indicate that the action was successful. If the controller indicates the action was unsuccessful, please repeat the procedure.
Include or exclude the ZDS-220 from the existing Z-Wave home control network with your primary controller.
- Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.
- When prompted by your primary controller, triple click the PROG button within 1 second.
(The unit will enter classical inclusion/exclusion first, then jump to NWI, and after 20 seconds, it will finally exit NWI mode automatically if there is no inclusion/exclusion request.)
- The primary controller should indicate that the action was successful. If the controller indicates the action was unsuccessful, please repeat the procedure.
Include or exclude the ZDS-220 from the existing Z-Wave home control network with your primary controller.
- Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.
- When prompted by your primary controller, triple click the PROG button within 1 second.
(The unit will enter classical inclusion/exclusion first, then jump to NWI, and after 20 seconds, it will finally exit NWI mode automatically if there is no inclusion/exclusion request.)
- The primary controller should indicate that the action was successful. If the controller indicates the action was unsuccessful, please repeat the procedure.
Factory reset Dimming Switch Module (Dual mode)
Step 1: Press and keep holding the PROG button for no less than 10 seconds.
• LED state will toggle for first 5 seconds of being pressed.
• LED state will toggle again after the remaining 5 seconds.
Step 2: Release the PROG button then triple click the PROG button within 2 seconds of step 1.
• LED will stay in previous ON or OFF stage.
Remark : Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Please note that this is a user manual Dimming Switch Module (Dual mode) from Remotec is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Dimming Switch Module (Dual mode) and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.