Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Plug-in Switch (Dual Plug Simultaneous Control) (39449 / ZW4106) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Plug-in Switch (Dual Plug Simultaneous Control) (39449 / ZW4106)from Resideo. To view other Z-Wave products and manuals from Resideo follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Plug-in Switch (Dual Plug Simultaneous Control)
SKU Code
39449 / ZW4106
Description
Transform any home into a smart home with the Resideo Z-Wave Plug-in Switch (Dual Plug Simultaneous Control). The lighting control enables wireless control of on/off functions for standard table and floor lamps and is compatible with incandescent, LED, Xenon, Halogen, fluorescent and compact fluorescent bulbs. Easily controlled by your mobile device or computer using any Z-Wave certified gateway, the space-saving horizontal module plugs into a standard wall receptacle without blocking the second outlet or obstructing placement of furniture. It provides dual Z-Wave enabled outlets for the lamp or appliance that you would like to control and a regular pass-through AC outlet for other electrical appliances. Perfect for plug-in fans, heaters, lamps and more! Take control of your home lighting with Resideo Z-Wave Smart Controls!
Version #
HW: 255 FW: 5.22 was the version certified
Certification #
ZC10-20036901
Certified
2020-03-27T16:52:45.101655
Z-Wave Version
6.51.10

Security

As a Z-Wave Plus certified product, Plug-in Switch (Dual Plug Simultaneous Control) supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    Resideo describes Plug-in Switch (Dual Plug Simultaneous Control) as having the following features:

    • Switch Load Capacity Current
    • Switch Load Capacity Watts
    • Switch Type
    • Loads Controlled
    • Firmware updatable via a compatible Z-Wave gateway
    • Color
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    ADDING YOUR DEVICE TO A Z-WAVE NETWORK
    1. Follow the instructions for your Z-Wave certified
    controller to add a device to the Z-Wave network.
    2. Once the controller is ready to add your device, press
    and release the manual/program button on the smart
    switch. Repeat as necessary to add the switch to
    the network.

    TO REMOVE AND RESET THE DEVICE
    1. Follow the instructions for your Z-Wave certified
    controller to remove a device from the Z-Wave network.
    2. Once the controller is ready to remove your device, press
    and release the manual/program button on the smart
    switch to remove it from the network.

    Factory reset Plug-in Switch (Dual Plug Simultaneous Control)

    TO RETURN YOUR SWITCH TO FACTORY DEFAULTS
    1. If plugged in, unplug the device from the receptacle.
    2. Press and hold the top button, plug the device in and
    continue to hold for at least 3 seconds.
    NOTE: This should only be used in the event your network’s
    primary controller is missing or otherwise inoperable.

    Please note that this is a user manual Plug-in Switch (Dual Plug Simultaneous Control) from Resideo is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Plug-in Switch (Dual Plug Simultaneous Control) and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.