The following is an overview of the user manual for the Z-Wave product Keyfob Remote Control (SK-5005-02)from Saykey. To view other Z-Wave products and manuals from Saykey follow that link.
Overview
trigger central scenes notification and/or controls max 8 devices in group turn on, off, stop. A special "SOS" key designs for
emergency notification. Further more, it can act as primary controller to add and control Z‐Wave device as standalone application.
The product supports acting as Z‐Wave primary controller to add (inclusion), remove (exclusion) device stand alone, meanwhile it
can associated device to control groups while the device was added, supports triggers control associated device in groups.
Also, It supports learn mode for added by other master controller, supports trigger central scene command to master controller, and
it can associated control devices by key‐fob local operation or master controller association set configuration.
Security
As a Z-Wave Plus certified product, Keyfob Remote Control supports Z-Wave S2 security. The following security modes are directly supported:
Features
Saykey describes Keyfob Remote Control as having the following features:
- Loads Controlled
- Supported Notification Types
- Z-Wave Scene Type
- Battery Quantity
- Battery powered using CR2032 batteries
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
1) Press and hold both ""On"" and ""Off"" key together for 2 seconds until LED indicator light on, release all key;
2) Press and hold ""Off"" key for 2 seconds until LED indicator flash quickly (1 second on, 1 second off), key‐fob starts remove device processing;
3) Refer to device manual, trigger the device which is going to included start network add/remove mode;
4) If key‐fob detects any device started network add/remove mode, it implement remove device procedure and LED indicator light on for 3 seconds after exclusion successful; If key‐fob has not detects any device in 15 seconds, exit remove device process and LED indicator turn off.
1) Press and hold both ""On"" and ""Off"" key together for 2 seconds until LED indicator light on, release all key;
2) Press ""Stop"" key 3 times in 2 seconds and LED indicator flash Flash on fast 3 times, then product keep in wakeup for 30 second without initial
wakeup parameter or 10 second has initial wakeup parameter.
Factory reset Keyfob Remote Control
1) Press and hold both ""On"" and ""Off"" key together for 2 seconds until LED indicator light on, release all key;
2) Press and hold both ""Stop"" and ""SOS"" key together for 10 seconds, during hold time LED will blink off 0.5 second interval 2 seconds. After hold 10 seconds LED indicator light off, then release all keys, factory default is retrieve, LED indicator will flashes three times after restore factory default success.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
User can protect key‐fob’s keyboard avoid un‐want press key‐fob keyboard by Protect Command Class.
Factory default un‐protect the keyboard, user can re‐configuration protect timeout value between 30 second to 60 second to enable keyboard protect function. From last key‐fob operation complete protect timeout or received protect command from master controller; key‐fob’s keyboard was protected no more keyboard except un‐protect sequence is acceptable.
1) Press and hold both ""On"" and ""Off"" key together for 2 seconds until LED indicator light on, release all key;
2) Press and hold ""On"" key for 2 seconds until LED indicator flash slowly (3 second on, 3 second off), key‐fob starts add device processing;
3) Refer to device manual, trigger the device which is going to included start network add/remove mode;
4) If key‐fob detects any device started network add/remove mode, it implement add device procedure and LED indicator light on for 3 seconds after inclusion successful; If key‐fob has not detects any device in 60 seconds, exit add device process and LED indicator turn off.
1) Press and hold both ""On"" and ""Off"" key together for 2 seconds until LED indicator light on, release all key;
2) Press and hold ""Stop"" key for 2 seconds until LED indicator intermittently flash (light on 2 times in 3 second), key‐fob starts copy controller network processing;
3) Refer to controller manual, trigger the controller which is going to copied starts network learn mode;
4) If key‐fob detects any controller started network learn mode, it implement copy controller procedure and LED indicator
light on for 3 seconds after copy successful; If key‐fob has not detects any device in 60 seconds, exit copy controller process and LED indicator turn off.
Please note that this is a user manual Keyfob Remote Control from Saykey is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Keyfob Remote Control and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.